£7.75 delivery on orders excluding certain products & postcodes *
Axalta ViterFloor EEF is an epoxy ester resin with great overall performance compared to traditional single pack floor coatings. ViterFloor EEF has good resistance to scuffing and spillages of oil, petrol, detergents and dilute aqueous chemical solutions. White spirit based, it is generally compatible with most existing systems.
Axalta ViterFloor EEF is suitable for use on concrete, stone, timber or primed steelwork. For easy application to light duty areas where regular cosmetic upgrades are organised.
All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination.
Bare Concrete: Remove dirt and contamination by detergent washing, flame cleaning or other appropriate means. For the best long term coating life, laitance should be removed by vacuum blast cleaning (recommended), power grinding or acid etching. If acid etching, more than one application may be required to produce a granular surface suitable for good adhesion. Vacuum blast cleaning should produce a surface profile appropriate to the thickness of the coating being applied. If laitance is not removed, it can detach in service along with the coating, leaving patchy areas of bare concrete.
Previously Painted Floors: Abrading (as well as thoroughly cleaning) the existing coating is always recommended to optimise adhesion. As ViterFloor EEF has a mild solvent blend, there should be minimal reaction with existing coatings, such as the lifting of old coating edges. A test area is recommended to confirm compatibility and that adequate adhesion can be achieved.
Wood Floors: Punch all nail heads down below the surface. Sand the surface down to clean, smooth wood using an industrial vacuum sander, cutting-in at edges with a hand sander. To give a smooth finish, it is recommended to also lightly sand and vacuum between coats.
Steel Floors: Please contact our technical team for further details.
Must be mixed thoroughly by using a mechanical agitator before use. Agitate periodically to ensure paint remains homogeneous.
The concrete surface must be dry and at least 12 weeks old. The moisture content of the concrete should not exceed 6% when measured 25mm below the surface (with e.g. a Protimeter measuring in 25mm drilled holes filled with gel), or 14% when measured with a surface moisture gauge (such as a Protimeter WME (Wood Moisture Equivalent) gauge).
Only apply in conditions of good ventilation, which must be maintained during drying and curing. Do not apply when rain, mist, sleet or snow are imminent. During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the substrate temperature should remain at least 3ºC above the dew point. Paint temperature should ideally be at a minimum of 15ºC.
Components: | Single Pack |
Type: | Epoxy Ester |
Finish: | Semi Gloss |
Stock Colours: | Tile Red, Mid Grey (Approx RAL 7001), Yellow RAL 1003 |
Tintable: | Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable |
VOC Content: | 456 g/L |
Volume Solids: | 40% |
Suitable Substrates: | Concrete, Stone, Timber or Primed Steelwork. |
Application Method: | Brush, Roller or Airless Spray |
Theoretical Coverage: | 8 - 13.3 m2 per litre |
Wet Film Thickness (WFT): | 75 - 100 microns |
Dry Film Thickness (DFT): | 30 - 50 microns |
Induction Time: | - |
Pot Life: | - |
Dust Dry: | 4 hours at 23°C at 40 microns |
Overcoatable: | After 16 hours at 23°C at 40 microns |
Fully Cured: | 7 days at 23°C at 40 microns |
Cleaner / Thinner: | Axalta 1050 Thinner |
Shelf Life: | Minimum 12 months if stored as above in unopened containers |
Packaging: | Available in 5 Litres |