Bradite Floor Finish CF22

SKU
id18093
UN1263 (Class: 3, Pk Grp: III)
For use on concrete and steel floors. Highly resistant to chemicals and oils.
Available in 5 Litres
£87.60 £73.00
In stock
Product Description

Bradite Floor Finish is a high performance single pack chlorinated rubber floor paint for use on concrete and steel floors. Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.

Best Uses

Bradite Floor Finish CF22 is suitable for use on concrete and steel floors, and is also highly resistant to chemicals and oils. It is suitable for interior and limited exterior use.

Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non-porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details.

High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil. Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.

Painting System

For application on concrete or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TC32 to allow penetration into the substrate.

1st coat Floor Finish CF22 (thinned, if required)
2nd coat Floor Finish CF22
3rd coat Floor Finish CF22

For maintenance painting the 1st coat will be a touch up to bare areas. While the coating will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C, and should not be subject to heavy traffic for at least 24 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity.

Technical Details

Certificates and Approvals

  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.
  • 2004/42/EC EU limit value for this product (cat.A/i sb): 500g/l (2010). This product contains max.498 g/l VOC.

Technical Info

Components: Single Pack
Type: Chlorinated Rubber
Finish: Eggshell (approx. 20%)
Stock Colours: Clear
Tintable: Yes, to most BS and RAL Colours. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 498 g/L
Volume Solids: 45%
Suitable Substrates: Concrete, steel, free of dust, efflorescence, dry and suitably prepared. Interior and limited exterior.
Application Method: Brush or Roller (Airless or Air-Atomised Sprays are not recommended)
Theoretical Coverage: 10 m2/L/coat
Wet Film Thickness (WFT): 100 microns/coat
Dry Film Thickness (DFT): 45 microns/coat
Induction Time: -
Pot Life: -
Touch Dry: 1 hour at 20°C
Overcoatable: After 12 hour minimum at 20°C
Fully Cured: 6 days at 20°C
Cleaner / Thinner: Bradite Thinner TB34 (clean with Bradite Thinner TC32)
Shelf Life: 12 months minimum in original unopened containers.
Packaging: Available in 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use