Bradite HB MIO Epoxy Build Finish EM97

SKU id19159 Part A and B: UN1263 (Class: 3, Pk Grp: III)
Hard wearing coating that is recoatable even after long periods of exposure
Available in 4.5 Litres
£64.65 (£77.58 Inc VAT)
*These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.
£64.65 (£77.58 Inc VAT)

Product Description

Bradite HB MIO Epoxy Build Finish EM97 is a two pack high build epoxy coating and finish, pigmented with micaceous iron oxide. Suitable as a high build coating or finish in systems for steel substrates.

Best Uses

Bradite HB MIO Epoxy Build Finish EM97 is best used as an intermediate build coat or finish on suitably primed steel and non-ferrous substrates. This product produces a tough, hard wearing coating that is recoatable even after long periods of exposure.

For internal & external steel & non-ferrous substrates which are dry, free of contamination and have been properly prepared and primed. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. (Note, not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints.)

Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Preparation – industrial protective coating

High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum).

1st coat Bradite Surface Tolerant Epoxy Primer EP92*
2nd coat Bradite HB MIO Epoxy Build Finish EM97
3rd coat Bradite Polyurethane Gloss Finish PG77
4th coat Bradite Polyurethane Gloss Finish PG77
* Substitute with Bradite Barrier Primer EU96 on galvanised metal, aluminium and other non-ferrous metal surfaces.

For maintenance painting the 1st coat will be a touch up to bare areas only. 

Preparation – wet blasted steel

High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil. Steel should be wet blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns then rinsed
with fresh water, with excess water being blown off with oil free compressed air. (For maintenance repair, wet blast as previous, feather existing coating to a sound edge and abrade to provide a key.)

Painting System

1st coat Bradite Surface Tolerant Epoxy Primer EP92
2nd coat Bradite HB MIO Epoxy Build Finish EM97
3rd coat Bradite Polyurethane Gloss Finish PG77

For maintenance painting the 1st coat will be a touch up to bare areas only.

Preparation – high temperature applications (200oC)

High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum).

Painting System

1st coat Bradite HB MIO Epoxy Build Finish EM97
2nd coat Bradite HB MIO Epoxy Build Finish EM97
3rd coat Bradite HB MIO Epoxy Build Finish EM97

Recommended Products To Use


Bradite Industrial Degreaser TD39

Bradite Industrial Degreaser TD39

Industrial degreaser for oily or soiled surfaces.

£11.38 (£13.66 Inc VAT)
Bradite Epoxy Thinner TE36

Bradite Epoxy Thinner TE36

Use for thinning epoxy paints and cleaning equipment.

£16.89 (£20.27 Inc VAT)
Bradite HB MIO Build Finish Coat AM60

Bradite HB MIO Build Finish Coat AM60

Perfect for the protection and decoration of ferrous & non-ferrous metals

£46.79 (£56.15 Inc VAT)