Centrecoat MMA Pourable Repair Mortar

SKU
ID23536
Part A: UN1866 (Class: 3, Pk Grp: II), Part B: UN3077 (Class: 9, Pk Grp: III)
A fast curing, high strength, two component Methacrylate Resin mortar, formulated for rapid and permanent repairs to concrete surfaces.
Available in 17 Kg in Light Grey
£118.94 £99.12
In stock
Product Description

Centrecoat MMA Pourable Repair Mortar is a fast curing, high strength, two component Methacrylate Resin mortar. For rapid and permanent repairs to concrete surfaces that may be subjected to heavy loading in service. Excellent resistance to dilute acids and alkalis, oil, petrol, and diesel.

Best Uses

Centrecoat MMA Pourable Repair Mortar is formulated for repair use on spalled or damaged concrete, bedding pre-cast concrete beams, chemical bunds and floor repairs.  Superior resistance to oil, petrol, diesel and dilute acids and alkalis, 

  • High Strength
  • Very good chemical resistance
  • Excellent adhesion to primed concrete
  • Fast curing, even at low temperatures
  • Impact and abrasion resistant
  • Frost resistant and impervious to water
  • Excellent mechanical properties
  • Excellent resistance to dilute acids and alkalis, oil, petrol, and diesel

Application

Remove all laitance, spalled concrete, grease, oil, dust, and other contaminants by scabbling, bush hammering, or other mechanical treatment, to provide a sound clean substrate. Any exposed reinforcing steel shall be fully exposed by cutting out around its full circumference, and cleaned by hand abrading or wire brushing to remove rust, scale, etc., and primed with a coat of Centrecoat MMA Multi-Use Primer.

The prepared concrete surface, together with the pre-primed re-bars, shall be primed by the application of Centrecoat MMA Multi-Use Primer. The mixed Centrecoat MMA Multi-Use Primer should be applied by brush or roller at a nominal rate of 0.2 - 0.3Kg per m2, depending upon surface profile. Allow the primer to cure for a minimum of 40 minutes.

Centrecoat MMA Pourable Repair Mortar is supplied as a two component product consisting of the BASE component, and the FILLER/CATALYST component. The contents of the BASE and FILLER / CATALYST component should be thoroughly mixed together for 1-2 minutes, until a uniform consistency is achieved. Mix using a low speed drill stirrer or a forced action mixer such as a Mixall, Pennine or Creteangle type.

Centrecoat MMA Pourable Repair Mortar shall be poured onto the primed floor and trowel finished. The material should not be feather edged. Minimum application thickness is 5mm. The product may be bulked out with 2-6mm quartz gravel for sections in excess of 15mm.

Clean equipment with Centrecoat MMA Tool Cleaner immediately after use.

Technical Details
Components: Two Pack
Type: MMA
Finish:
Stock Colours: Light Grey
Tintable: No
VOC Content:
Volume Solids:
Suitable Substrates: For concrete
Application Method: Trowel
Theoretical Coverage: A 17 Kg pack yields 8.5 Litres of mortar, sufficient for 0.85m2 @ 10mm thickness.
Wet Film Thickness (WFT):
Dry Film Thickness (DFT): Minimum 5mm
Induction Time: -
Pot Life: 15 - 20 minutes at 20°C
Foot Traffic: 1 hour at 20°C
Overcoatable:
Traffic Ready: 2 hours at 20°C
Cleaner / Thinner: Clean equipment with Centrecoat MMA Tool Cleaner immediately after use.
Shelf Life: Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C. Adequate ventilation of the storage area should
be provided. Keep containers tightly closed when not in use Centrecoat MMA Pourable Repair Mortar has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions.
Packaging: Available in 17 Kg
Product Video