Centrecoat ArmourCoat UltraGrip 3

SKU
id24902
Non Hazardous
A heavy duty, 3 part flexible binder which when broadcasted with natural or synthetic aggregates creates a slip resistant surface.
Available in 28.66 Kg. Contains Resin, Hardener and Aggregate
£111.30 £92.75
In stock
Product Description

Centrecoat ArmourCoat UltraGrip 3 is a heavy duty, 3 part flexible binder which when broadcasted with natural or synthetic aggregates creates a slip resistant profiled surface.

Best Uses

Centrecoat ArmourCoat UltraGrip 3 is suitable for car parks, ramps and pedestrian walkways when broadcasted with a compatible aggregate. Suitable aggregates are washed and dried bauxites, granites or basalts (natural or coloured).

  • For vehicular use, use 1 - 3mm aggregate
  • For pedestrian use, use 0.5 - 1.5mm aggregate

Centrecoat ArmourCoat UltraGrip 3 is suitable for use on concrete, polymer modified sand/cement screeds, suitable asphalt, wood and steel surfaces. UltraGrip 3 is hard wearing, tough and slightly flexible. It provides a seamless finish with rapid installation and minimal downtime.

Contains resin, hardener and aggregate.

Application

Centrecoat ArmourCoat UltraGrip 3 can be applied at temperatures between 5 - 30ºC. At low temperatures the material will exhibit less flow than at warmer temperatures and may be more difficult to apply at low thicknesses. The maximum substrate and atmospheric relative humidity should be 75%. The substrate and uncured floor must be kept at least 3ºC above the dew point to reduce the risk of condensation or blooming on the surface, from before priming to at least 24 hours after application. Surfaces must be completely dry before installation otherwise the material may blister and/or de-bond.

Inadequate preparation will lead to loss of adhesion and failure. Follow instructions on the data sheet prior to application.

A primer is not always necessary as Centrecoat ArmourCoat UltraGrip 3 has excellent bond strength to well prepared concrete, sand/cement screeds, suitable asphalt, timber and steel. Bond strength testing to BS EN 13892-8 should be carried out where doubt exists. Where there is a risk of excessive resin absorption into the substrate due to high surface porosity, Centrecoat ArmourCoat Multi-Use Primer should be used. Surfaces should have a relative humidity of <75%. Where the substrate relative humidity is >75%, Centrecoat Armourcoat Epoxy DPM should be used.

Follow data sheet instructions for application.

Technical Details
Components: Three Pack
Type: Epoxy Resin
Finish: Profiled Aggregate
Stock Colours: Natural Buff / Beige
Tintable: No
VOC Content: <500 g/L
Volume Solids:
Suitable Substrates: For use on concrete, polymer modified sand/cement screeds, suitable asphalt, wood and steel surfaces.
Application Method: Steel Float, Pin Rake or Squeegee and Spike Roller
Theoretical Coverage: 1.8 kg/m2 per mm thickness. Minimum 2 mm thickness. The applied thickness should be approximately half the nominal particle size of the broadcast aggregate.
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: -
Pot Life: 10 minutes at 20°C
Light Foot Traffic: 6 hours at 20°C
Overcoatable:
Fully Cured: 24 hours at 20°C
Cleaner / Thinner:
Shelf Life: Store off the ground in unopened packs in a dry store, under cover between 10ºC and 30ºC out of direct sunlight. Protect from frost.
Packaging: Available in 28.66 Kg

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use