Tintable to a wide range of RAL and BS shades, this semi matt high build primer / finish is an ideal solution to protect metal and Plastisol cladding as well as structures such as Modular Buildings. This multi-functional product is designed for application directly onto cladding, and to provide good phosphate-based anti-corrosive protection for iron and steel, whilst being tolerant to application directly onto wood and over suitably prepared old paintwork.
This product is designed for application by airless and air-assisted airless spray using a 15-17 thou tip with 50° fan, as well as by conventional spray, brush and roller when thinned appropriately (which will not render the product non-compliant).
Centrecoat HB Anti-Corrosive Cladding Paint can be applied onto previously painted substrates, most types of metal cladding, iron, steel, wood and modular buildings. However, when repainting PVF2 cladding, a surface tolerant primer is required as a first coat to ensure adequate adhesion.
Apply only to clean, dry and suitably prepared surfaces. On old paintwork, remove all loose and flaky paint back to a firm edge. On all substrates, clean off any oil or greasy residues, dust, scale, rust, etc. The surfaces to be painted should then be lightly flatted, to give a smooth surface with an adequate key, before the application of this product. Coating adhesion and performance is in general proportional to the degree of surface preparation.
This product is supplied ‘ready for use’ airless spray application. If required, it should be thinned slightly. In hot weather, it may be necessary to add additional solvent to compensate for evaporated solvent. Normal thinning is unlikely to affect the compliant nature of this product. Do not apply or dry when air or surface temperature is below 5°C, above 30°C or in high humidity or where condensation is likely to occur (i.e. Surface temperature must always be a minimum of 3°C above dew point). Painting should only be carried out under good atmospheric conditions and clement weather.
Painting in direct sunlight can lead to a patchy appearance if the surface temperature is in excess of 30°C. Preparation, painting and drying should never be undertaken: when the air temperature falls below the minimum temperature for the coating, or during fog, mist, snow, or when rain is imminent, or when the surface to be painted is wet with condensation or when condensation may occur during the drying period.
|Stock Colours:||All colours are tinted with the exception of standard black|
|Tintable:||Yes, to most RAL and BS Colours. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||390.0g per Litre|
|Volume Solids:||50 - 55%|
|Suitable Substrates:||For application directly onto cladding, iron and steel, wood or old paintwork|
|Application Method:||Brush, Roller, Air Atomised Spray or Airless Spray|
|Theoretical Coverage:||6.9m2 per litre|
|Wet Film Thickness (WFT):||77 - 185 microns|
|Dry Film Thickness (DFT):||80 - 100 microns (in 2 coats)|
|Touch Dry:||1 hour 30 minutes at 20°C|
|Overcoatable:||2 hours at 20°C|
|Fully Cured:||1 week at 20°C|
|Cleaner / Thinner:|
|Shelf Life:||12 months when stored indoors, in original unopened containers, within the temperature range 10ºC to 32ºC. Mix thoroughly before use.|
|Packaging:||Available in 5 and 20 Litres (4 x 5 Litres)|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.
Formulated for thinning and cleaning up alongside our Centrecoat HB Anti-Corrosive Cladding Paint.
A modified two pack epoxy adhesion and stabilising primer, specially formulated for the maintenance and repair of architectural cladding.
A universal heavy duty, direct to metal, waterborne, elastomeric, rust preventative paint.