This product is now discontinued. Please contact our technical team for a suitable alternative.
Sika Sikafloor 316 is a two component very low VOC, glossy clear coat based on polyurea technology used as part of a system to seal Sikafloor epoxy and tough elastic polyurethane flooring.
Sika Sikafloor 316 is a glossy clear coat that is used as part of a system to seal Sikafloor® epoxy and tough elastic polyurethane flooring.
- Based on polyurea technology
- Low odour
- Good UV resistance
- UV inhibitor
- Easy to clean
- Highly scratch resistant
- Good chemical resistance
Sikafloor®-316 can be used as clearcoat on Sika Decoflake, Sika Decofloor, Sika Compactfloor and Sikafloor-264 system build-ups. Please refer to the respective System Data Sheets.
Sika Sikafloor®-316 may only be used by experienced professionals.
The surface must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by vacuum. Pull off strength shall not be less than 1.5 N/mm2. If in doubt apply a test area first.
Prior to mixing, ensure part A is homogeneous, pour part A into part B and mix continuously for 3 minutes until a uniform mix has been achieved. After mixing A and B, 2 % by weight of Sika Antiskid Agent or Glass Beads must be added to the mix. The aggregates create a better skid resistance, improve the wetting properties of the product and may hide the possible imperfections in the subfloor. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.
Sikafloor®-316 must be thoroughly mixed using a electric stirrer or other suitable equipment.
When installing Sikafloor®-316, make use of Microfibre rollers with a fibre length of ~10 mm and a paint grid. A seamless finish can be achieved if a “wet” edge
is maintained during application.
- Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 02 08 01 04 034 0 000001 2017, and provided with the CE marking.
- Coating for surface protection of concrete accordingto EN 1504-2:2004 for principles 2,3,5,6,8, Declaration of Performance 02 08 01 04 034 0 000001 2017,certified by notified factory production control certification body 0921, and provided with the CE marking.
|VOC Content:||140 g/L|
|Suitable Substrates:||Sikafloor®-316 can be used as clearcoat on Sika Decoflake, Sika Decofloor, Sika Compactfloor and Sikafloor-264 system build-ups.
Please refer to the respective System Data Sheets..
|Application Method:||Microfibre Roller|
|Theoretical Coverage:||On smooth surfaces: ~0.07 - 0.08 kg per m² per layer
On broadcasted / flaked surfaces: ~0.1 - 0.12 kg per m² per layer
In case of broadcasted with corundum ~0.13 - 0.14 kg per m
|Wet Film Thickness (WFT):||-|
|Dry Film Thickness (DFT):||-|
|Pot Life:||60 minutes at 20°C|
|Foot Traffic:||16 hours at 20°C|
|Light Traffic:||36 hours at 20°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||Clean all tools and application equipment with solvent immediately after use. Hardened and/or cured material can only be removed mechanically.|
|Shelf Life:||12 months from date of production|
|Packaging:||Available in 5 Kg|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.