Sika Sikafloor 359 N

SKU
ID15727
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: Non Hazardous
A two component, PUR tough elastic coloured seal coat for industrial flooring such as car park decks, ramps or warehouses.
Available in 32.5 Kg. Tintable to almost an unlimited colour range.
From £953.95 £794.96
In stock
Only %1 left
Product Description

Sika Sikafloor 359 N is a two component, PUR tough elastic coloured seal coat for industrial flooring such as car park decks, ramps or warehouses.

Best Uses

Sika Sikafloor 359 N is suitable as an abrasion resistant seal coat with high mechanical resistance for broadcast systems with crack-bridging properties in industrial flooring. 359N is particularly suitable for car park decks, ramps and warehouses etc.

  • Tough-elastic
  • Good mechanical and chemical resistance
  • Watertight
  • Good opacity
  • Non-yellowing
  • Matt finish
  • Easy application
  • Slip resistant surface possible

Application

For application details for specific systems, please see Product Data Sheet for details.

The concrete substrate must be sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum pull off strength of 1.5 N/mm2. The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. If in doubt, apply a test area first.

Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured surface. Weak concrete must be removed and surface defects such as blowholes and voids must be fully exposed. Repairs to the substrate, filling of blowholes/voids and surface levelling must be carried out using appropriate products from the Sikafloor®, SikaDur® and SikaGard® range of materials. The concrete or screed substrate has to be primed or levelled in order to achieve an even surface. High spots must be removed by e.g. grinding. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush and/or vacuum.

Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 3 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.

 

IMPORTANT NOTICE: From 24th August 2023, adequate training is required before industrial or professional use of this product. Training can be accessed at: https://www.safeusediisocyanates.eu

Technical Details

Approvals

  • Coating for concrete protection according to the requirements of EN 1504-2:2004 and the EN 13813:2002, DoP 2080104002500000011008 certified by Factory Production Control Body, 0921 and provided with the CE-mark.
  • Certified as part of the Surface Protection System OS 11a according to DIN EN1504-2 and DIN V 18026.
  • Certified as part of the Surface Protection System OS 11b according to DIN EN1504-2 and DIN V 18026

Systems

Sika Sikafloor 359 N is used within the following Sika systems:

  • Sikafloor EB 24 System 
  • Sikafloor MultiFlex PB 21 UV
  • Sikafloor MultiFlex PB 26 UV
  • Sikafloor MultiFlex PB 32 UV
  • Sikafloor MultiFlex PB 51 UV
  • Sikafloor MultiFlex PB 52 UV
  • Sikafloor MultiFlex PB 55 UV
  • Sikafloor MultiFlex PB 57 UV

See Data Sheets tab for System sheet downloadable PDF.

Technical Info

Components: Two Pack
Type: Polyurethane
Finish: Matt
Stock Colours: RAL 3003, RAL 5010, RAL 6010, RAL 7016, RAL 7031
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: <500 g/L
Volume Solids: 85%
Suitable Substrates: Concrete
Application Method: Squeegee, Short Pile Roller
Theoretical Coverage: 0.7–0.9 kg/m2/layer. Please refer to the respective System Data Sheet.
Wet Film Thickness (WFT): Please refer to the respective System Data Sheet.
Dry Film Thickness (DFT): Please refer to the respective System Data Sheet.
Induction Time: -
Pot Life: 25 minutes at 20°C
Foot Traffic: 24 hours at 20°C
Overcoatable:  
Fully Cured: 7 days at 20°C
Cleaner / Thinner: Clean all tools and application equipment with Sika Thinner C immediately after use.
Shelf Life: 1 years minimum in original unopened containers.
Packaging: Available in 32.5 Kg
Product Video

Related Products