Bedec Acrylic Water Based Floor Paint is formulated for interior concrete and wooden floors without the need for a separate primer. Can be used for cement, stone, brickwork, timber floors and MDF also.
Bedec Acrylic Water Based Floor Paint is ideally suited for the protection of interior concrete or wooden floors. This acrylic system is an easy to apply, durable, self cross linking acrylic coating with excellent colour retention. This product is highly recommended to coat interior concrete and wooden floors. A thinned coat of Bedec Acrylic Floor Paint diluted with approximately 30% clean water is used as a primer. This low odour, slip resistant floor paint from Bedec offers a quick drying and durable coating of high quality paint. Bedec acrylic floor paint is slip resistant, which makes it ideal for almost any different environment. Promain cannot stress the importance of having an anti slip surface, this helps towards the prevention of injuries to employees and general domestic users.
Bedec Acrylic Water Based Floor Paint is suitable for coating both wooden and concrete floors in areas such as workshops with foot traffic. This product is however not suitable for home garages or areas with high trafficking such as warehouses. The primary use for this floor paint is to be used for coating light industrial floors and new concrete. Promain seeks to provide you with products that we would use only ourselves, and having tried and tested this product, we are sure you will be completely satisfied with the finish you get.
- Alkali resistant.
- Slip resistant.
- Low odour.
- Self priming.
- Quick drying.
- Easy to apply.
- Semi gloss finish.
- Can be used on new concrete without acid neutralisation.
- Suitable for concrete, cement, stone, brickwork, timber floors, MDF etc.
Ensure the surfaces to be painted are clean dry and free from dust, dirt grease and wax. Remove all loose and defective paint. Algal, fungal or mould growths should be removed and treated with a fungicidal wash. Smooth glossy surfaces should be lightly abraded to provide a key.
Bare steel should be free from rust, scale and dust. Before applying Bedec Waterbased All Metals Primer. New planed, finished wood or PSE wood should also be abraded to open the grain and allow maximum penetration. On new wood, cement render or any porous substrate. The first coat should be thinned with 30-40% clean water. New concrete may be extremely porous and a test area should be carried out to determine actual coverage rate that can be achieved. Where there is a risk of wood staining (Extractive discolouration) treatment with Bedec Stain Block is recommended. It is always advisable to test for staining by applying Floor Paint to a small area first.
Knots should also be treated with Bedec Stain Block, Knotting solution is not recommended. Ensure any laitance is washed off and removed prior to painting. Not recommended for power floated concrete floors, unless scarified to improve adhesion.
Ensure any laitance is washed off and removed prior to painting. Not recommended for power floated concrete floors, unless scarified to improve adhesion.
This product is highly recommended to coat interior concrete and wooden floors without the need for a separate primer. Other surfaces which Bedec Acrylic Water Based Floor Paint can be used for are cement, stone, brickwork, timber floors and MDF. This product is suitable for light industrial use such as workshops.
|Stock Colours:||Battleship Grey, Black, Blue, Clear, Dark Green, Light Grey, Tile Red, White and Yellow|
|Tintable:||Upon Special Request, Depending on Quantity. Please note, bespoke tints are non refundable / exchangable.|
|VOC Content:||140.0g per Litre|
|Suitable Substrates:||For Interior Cement Rendering, Stone, MDF, Chipboard, Hard and Soft wood and Most Types of Plastic|
|Application Method:||Brush or Roller|
|Theoretical Coverage:||10 -13 m2 per litre per coat|
|Wet Film Thickness (WFT):||85 microns|
|Dry Film Thickness (DFT):||32 microns|
|Touch Dry:||2 - 4 hours at 18°C|
|Overcoatable:||4 hours at 18°C|
|Fully Cured:||16 - 24 hours at 18°C|
|Cleaner / Thinner:||Clean up with warm soapy water|
|Shelf Life:||24 months|
|Packaging:||Available in 2.5, 5 and 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.