Remmers Epoxy BS 3000 SG New Floor Paint

SKU
ID17608
Part A: Non Hazardous, Part B: UN3082 (Class: 9, Pk Grp: III)
High quality, silk gloss, water based, epoxy resin floor paint.
Available in 5, 10 and 25 Kg
From £92.34 £76.95
In stock
Only %1 left
Product Description

Remmers Epoxy BS3000-SG New, 2-component, water based epoxy resin floor paint with a wide range of applications. Suitable for garage floors, workshop or shop floors.

Best Uses

Remmers Epoxy BS 3000 SG New is used as a sealant in the Remmers Water Vapour Diffusion-Open System. Application examples include Production Rooms, Warehouses and Workshops, shops etc. Benefits include:

  • Silk gloss
  • Low odour
  • Water vapour diffusion open
  • Can be subjected to mechanical and chemical loads
  • Can be subjected to vehicle traffic
  • Can be made slip-resistant
  • Physiologically safe
  • Suitable for indoor areas

The substrate must be load-bearing, dimensionally stable, sound, free of loose material, dust, oil, grease, marks from rubber tyres or other substances that could interfere with adhesion. Tensile strength of the substrate must be1.5 N/mm² on average and compressive strength at least 25 N/mm². The substrate must also have sufficiently reacted and be load-bearing.

  • Concrete max. 6 % by mass
  • Cement screed max. 6 % by mass

Application

The substrate must be prepared by suitable means so that it meets the specifications given above, e.g. by steel shot blasting or diamond grinding. Fill broken out and missing areas flush with the surface using the Remmers PCC System or one of the Remmers EP Mortars. Then prime and, if necessary, level. Full application instructions can be found on the Technical Data Sheet.

Technical Details

Systems

  • Remmers SS320 - Epoxy BS3000 Breathable Coating Systems (DFT = 350 - 400µ)
  • Remmers SS320+ - Epoxy BS 3000 Breathable Systems (DFT = 300 - 350µ)

See technical tab for downloadable System Sheets.

Notes

All of the values and application rates given were determined under laboratory conditions (20 °C) with standard shades of colour. When worked at the building site, these values may deviate slightly. The coating system has a slightly textured surface which is typical for this type of system.

Technical Info

Components: Two pack system
Type: Epoxy Resin Binder / Sealant
Finish: Silk Gloss
Stock Colours: RAL 7032, RAL 7001, RAL 7035, RAL 7030, RAL 7012
Tintable: Yes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: < 140 g/l
Volume Solids: 65%
Suitable Substrates: Suitable for indoor areas
Application Method: Brush or Roller
Theoretical Coverage: Primimng: approx. 0.15 - 0.20 kg/m² per working operation. Sealant: approx. 0.20 - 0.25 kg/m² per coat
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Working Temperature: Minimum 8°C and Maximum 30°C - The substrate must also be at least 3°C above the dew point
Pot Life: 30 minutes at 20°C
Waiting Time: Minimum of 16 hours and maximum of 48 hours at 20°C
Drying Time: Foot Traffic after 1 day, Mechanically loadable after 3 days at 20°C
Fully Cured: Full loading capacity after 7 days days at 20°C
Cleaner / Thinner: -
Shelf Life: At least 9 months unopened
Packaging: Available in 1 Kg, 5 Kg, 10 Kg and 25 Kg

Related Products