Sika Sikafloor 264 N Thixo

SKU
ID4061
UN3082 (Class: 9, Pk Grp: III)
A hard wearing, seamless, low maintenance, textured gloss and slip resistant finish internally to floors.
Available in 30 Kg
From £875.76 £729.80
In stock
Only %1 left
Product Description

Sikafloor 264 N Thixo is a two part epoxy coloured thixotropic resin that provides a hard wearing, seamless, low maintenance, textured gloss and slip resistant finish internally to floors.

Best Uses

Sikafloor 264 N Thixo can be used to provide slip resistance to floors in storage rooms, assembly halls, maintenance workshops, garages and loading ramps that are prone to become slippery due to the surrounding environment. Sikafloor 264 N Thixo can be used to provide good chemical and mechanical resistance with a glossy finish.

Used within the Sikafloor MultiDur ET 15 system.

  • Seamless
  • Good chemical and mechanical resistance
  • Easy application
  • Waterproof
  • Gloss finish
  • Easy cleanable slip resistant surface
  • Slip resistant surface to suit clients requirements without use of aggregates
  • Low maintenance

Sika Sikafloor 264 N may only be used by experienced professionals.

Application

The concrete substrate must be sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum pull off strength of 1.5 N/mm2. The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured surface. Weak concrete must be removed and surface defects such as blow holes and voids must be fully exposed.

Repairs to the substrate, filling of blowholes/voids and surface levelling must be carried out using appropriate products from the Sikafloor®, Sikadur® and Sikagard® range of materials. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush or vacuum.

Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 3 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a smooth consistent mix. Over mixing must be avoided to minimise air entrainment.

Prior to application, confirm substrate moisture content, relative air humidity and dew point. If > 4 % pbw moisture content, Sikafloor® EpoCem® may be applied as a T.M.B. (temporary moisture barrier) system.

Primer
Ensure a continuous, pore free coat covers the substrate. If necessary, apply two priming coats. Apply Sikafloor®-156 /-161 /-160 by brush, roller or squeegee. Preferred application is by using a squeegee and then backrolling in two directions at right angles to each other.

Levelling
Rough surfaces need to be levelled first. Therefore use e.g. Sikafloor®-156 /-161 /-160 levelling mortar (see PDS).

High Build Textured Coating
Sikafloor®-264 N Thixo is poured and spread evenly by means of a serrated trowel and then using a textured roller selected to achieve the required finish. Backroller
in two directions at right angles to each other.

Seal Coat
Apply seal/top coat of Sikafloor®-264 N Thixo by squeegee at a consumption of 0.6–0.8 kg/m2. Then using a textured roller selected to achieve the required finish. Back roller in two directions at right angles to each other.

Technical Details

Systems

Sika Sikafloor 264 N Thixo is used within the following Sika systems:

  • Sikafloor MultiDur ET-14
  • Sikafloor MultiDur ET-14 ECC
  • Sikafloor MultiDur ET-15

See Data Sheets tab for System sheet downloadable PDF

Technical Info

Components: Two Pack
Type: Thixotropic Resin
Finish: Textured Gloss
Stock Colours: RAL 3003, RAL 6010, RAL 7011, RAL 7032, RAL 7035, RAL 7037, RAL 9005, RAL 9010
Tintable: Yes, upon request. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 500 g/L
Volume Solids: 100%
Suitable Substrates: For concrete flooring
Application Method: Serrated Trowel and Textured Roller
Theoretical Coverage: 0.5 - 0.8 Kg per m2
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: -
Pot Life: 25 minutes at 20°C
Surface Dry: See datasheet
Overcoatable: See datasheet
Fully Cured: See datasheet
Cleaner / Thinner: Clean all tools and application equipment with Sika Thinner C immediately after use. Hardened and / or cured material can only be removed mechanically.
Shelf Life: 24 months from date of production in original unopened containers
Packaging: Available in 30 Kg

Related Products