Bradite Chlorinated Rubber is a high performance single pack chlorinated rubber Gloss / Eggshell finish with excellent chemical & water resistance.
Bradite Chlorinated Rubber is for ferrous, non-ferrous, concrete such as swimming pools and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Note: This is unsuitable for epoxy tar & bitumen paints, Portland cement, marble & tiled surfaces.
Bradite Chlorinated Rubber is ideal for milking parlours and other areas subject to chemical exposure and regular cleaning.
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.
When painting new concrete it is vital to ensure the substrate is fully cured and free of laitance. Power floated, shiny or unpainted non porous concrete should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37. High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. For best performance, complete vacuum blast cleaning of the substrate is recommended. Bradite TD39 industrial strength detergent washing and rinsing should be used with scrubbing to remove grease or oil. Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.
Galvanised steel, aluminium and other non-ferrous metal substrates should be roughened by mechanical abrading or sweep blasting with inert grit. Steel should be blast cleaned to SIS-Sa 2½ minimum, blast profile 35-50 microns and surface free of soluble salts, or de-rusted manually or mechanically to SIS-St 3 minimum.
For full painting details on Concrete Swimming Pools, and Industrial New Build and Maintenance, please see the product data sheet or contact our Technical Team for further advice.
|Finish:||Gloss or Eggshell|
|Tintable:||Yes, to most BS or RAL colours. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||Gloss - 548 g/L, Eggshell - 524 g/L|
|Suitable Substrates:||Steel and non-ferrous metals|
|Application Method:||Brush, Roller, Airless Spray or Conventional Air Spraying|
|Theoretical Coverage:||Gloss - 12 m2/L/coat, Eggshell - 10 m2/L/coat|
|Wet Film Thickness (WFT):||Gloss - 84 microns/coat, Eggshell - 100 microns/coat|
|Dry Film Thickness (DFT):||Gloss - 38 microns/coat, Eggshell - 45 microns/coat|
|Touch Dry:||30 minutes at 20°C|
|Overcoatable:||Gloss - 12 hours minimum, Eggshell - 8 hours minimum|
|Fully Cured:||6 days at 20°C|
|Cleaner / Thinner:||Bradite Thinner TC32|
|Shelf Life:||12 months minimum in original unopened containers|
|Packaging:||Available in 5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.