£7.75 delivery on orders excluding certain products & postcodes *
Centrecoat MMA Multi-Use Primer
SKU
ID23553
Part A: UN1866 (Class: 3, Pk Grp: II), Part B: UN3106 (Class: 5.2)
A general purpose primer for Centrecoat MMA coatings used on concrete, block paving, mortars, and screeds.
Available in 5 Kg
£127.44
£106.20
In stock
Product Description
Centrecoat
Centrecoat
MMA Multi-Use Primer. Used prior to any of the Centrecoat MMA range of coatings, mortars, and screeds. MMA Primer offers outstanding adhesion to concrete, block paving, steel, masonry, and marine plywood.
Best Uses
Centrecoat MMA Multi-Use Primer exhibits outstanding adhesion to concrete, block paving, as well as steel, masonry, and marine plywood. Centrecoat MMA Multi-Use Primer has fast curing characteristics to allow for rapid application of subsequent coatings, mortars or screeds. MMA Multi-Use Primer is often over coatable in less than 30 minutes.
- Rapid cure, even at low temperatures
- Very good chemical resistance
- Excellent adhesion
- Impervious to water
- Pre-packed units ready for use
- Easily applied
Centrecoat MMA Multi-Use Primer is supplied as a two pack material, comprising pre-weighed amounts of Base and Catalyst components. The mix ratio is fairly tolerant to variations within the range of 1% to 5% addition of Catalyst, so that part packs may be used if care is exercised.
Application
Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc. Suitable mechanical treatment such as vacuum grit blasting or mechanical scabbling is
recommended to ensure the removal of contaminants and to provide a mechanical ‘key’ for the primer.
Pour the contents of the CATALYST container into the BASE container and thoroughly mix, preferably by mechanical means.
Apply by squeegee to distribute evenly over the floor, and then use a long nap lambswool roller to achieve a nominal application rate of 0.25-0.30kg/m2. Allow to cure for a minimum of 40 minutes prior to applying any other of the Centrecoat MMA product range. If an interval of more than 8 hours between primer application and subsequent overcoating is anticipated then the primer shall be scattered with fine silica sand before hardening.
Clean equipment with Centrecoat MMA Tool Cleaner immediately after use.
Technical Details
| Components: | Two Pack |
| Type: | MMA |
| Finish: | |
| Stock Colours: | Straw Coloured Liquid |
| Tintable: | No |
| VOC Content: | |
| Volume Solids: | |
| Suitable Substrates: | Steel, masonry, marine plywood. |
| Application Method: | Squeegee and Long Nap Lambswool Roller |
| Theoretical Coverage: | A 5kg pack is sufficient to prime an area of 15-20m². Exceptionally porous surfaces may require a second coat. |
| Wet Film Thickness (WFT): | |
| Dry Film Thickness (DFT): | |
| Induction Time: | - |
| Pot Life: | 15 minutes at 20°C |
| Surface Dry: | |
| Overcoatable: | 40 minutes at 20°C |
| Fully Cured: | |
| Cleaner / Thinner: | Clean equipment with Centrecoat MMA Tool Cleaner immediately after use. |
| Shelf Life: | Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C. Adequate ventilation of the storage area should be provided. Keep containers tightly closed when not in use. Minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions. |
| Packaging: | Available in 5 Kg |
