Bradite Rapid Floor Paint PW74 is a high performance single pack moisture cure polyurethane floor coating for Interior concrete, wood or steel floors. Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.
Bradite Rapid Floor Paint is for use on interior concrete, wood or steel floors requiring a tough, quick drying, hard wearing flexible floor coating with good chemical and excellent water resistance. It can also be used with Bradite Low Slip Additives SA14 or SA12 to provide additional under foot traction (see Notes section for more details). This product is intended for professional use only.
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.
Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non-porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details.
High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil. Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting. Substrate should be dust free and completely dry before coating.
For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with Bradite Thinner TP33 to allow penetration into the substrate.
1st coat Bradite Rapid Floor Paint PW74 (thinned)
2nd coat Bradite Rapid Floor Paint PW74
3rd coat Bradite Rapid Floor Paint PW74
For maintenance painting the 1st coat will be a touch up to bare areas only. While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C, and should not be subject to heavy traffic for at least 48 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity. Due to the rapid drying of Bradite Rapid PW74 it is advised that once opened the can should not be resealed.
Certificates and Approvals
- Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.
- 2004/42/EC EU limit value for this product (cat.A/I sb): 500g/l (2010). This product contains max.300g/l VOC.
|Stock Colours:||Light Grey, Red|
|Tintable:||Yes, to most BS and RAL colours. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||276 g/L|
|Suitable Substrates:||Concrete, wooden, steel floors|
|Application Method:||Brush & Roller|
|Theoretical Coverage:||10 m2/L/coat|
|Wet Film Thickness (WFT):||100 microns/coat|
|Dry Film Thickness (DFT):||69 microns/coat|
|Pot Life:||Due to the rapid drying of Bradite Rapid PW74 it is advised that once opened the can should not be resealed|
|Touch Dry:||2 hours at 20°C|
|Overcoatable:||After 8 hours minimum at 20°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||Bradite Thinner TP33|
|Shelf Life:||6 months minimum in original unopened containers.|
|Packaging:||Available in 5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.