Hempel Hempadur Quattro 17634

SKU
id19247
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN3469 (Class 3,8, Pk Grp: III)
A universal epoxy and self-primed high performance coating system.
Available in 20 Litres
From £191.24 £159.37
In stock
Only %1 left
Product Description

Hempel Quattro 17634 is a two-component universal epoxy paint, which cures to a hard and tough coating with good resistance to abrasion, seawater and various oils.

Best Uses

Hempel Quattro 17634 is best used as a universal epoxy and self-primed high performance coating system for atmospheric or in-water service, including water ballast tanks and cargo oil tanks to be coated according to IMO-PSPC requirements (Resolutions MSC.215(82) and MSC.288(87)). Also recommended for long time corrosion protection of structural steel and concrete in severe corrosive and immersed environments.

HEMPADUR QUATTRO 17634 is intended for all year application down to -10°C/15°F and for in-shop applications where fast re-coating and handling is required

Application

New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G). Apply immediately after cleaning. All damage of shop primer and contamination from storage and fabrication should be thoroughly cleaned prior to overcoating. For repair and touch-up use: HEMPADUR QUATTRO 17634.

Ballast tanks and cargo oil tanks: See separate APPLICATION INSTRUCTIONS

Steel, maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to St 3 (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the performance of the paint. As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat must appear with roughened surface after the water jetting.

By water jetting to steel, cleanliness shall be Wa 2 - Wa 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). A flash-rust degree of maximum M (atmospheric exposure), preferably L (immersion) (ISO 8501-4:2006) is acceptable before application. Feather edges to sound and intact paint. Dust off residues. Touch up to full film thickness. On pit corroded surfaces, excessive amounts of salt residues may call for water jetting or wet abrasive blasting, alternatively dry abrasive blasting followed by high pressure fresh water hosing, drying, and finally, dry abrasive blasting again. Other substrates: contact Hempel.

Technical Details

Certificates and Approvals

  • PSPC type approved. (Consult HEMPEL for specific Type Approval Certificates)
  • Tested according to section 175.300 of the Code of Federal Regulations Title 21 - Dry Foodstuff. Consult Hempel for details
  • Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain
  • Approved as a low flame spread material when used as part of a predefined paint system
  • Norsok M-501 system no. 1 (Pre-Qualified)
  • Norsok M-501 system no. 3B (Pre-Qualified)
  • Norsok M-501 system no. 3C

Features

  • Excellent anticorrosive and very good mechanical properties
  • Short drying time
  • Curing down to -10°C/14°F
Components: Two Component
Type: Epoxy Paint
Finish: Semi-Flat
Stock Colours: Red / 50530 & Grey / 12170
Tintable: No
VOC Content: 276 g/l
Volume Solids: 72 ± 2
Suitable Substrates: Steel
Application Method: Airless spray / Brush / Roller
Theoretical Coverage: 5.8 m2/l [232.6 sq.ft./US gallon] - 125 micron/5 mils
Wet Film Thickness (WFT): 175 micron [7 mils]
Dry Film Thickness (DFT): 125 micron [5 mils]
Induction Time: -
Pot Life: 2 hour(s) 20°C/68°F
Surface Dry: 2 hour(s) 20°C/68°F
Overcoatable: See REMARKS on product Data Sheet
Fully Cured: 7 day(s) 20°C/68°F
Cleaner / Thinner: 08450 (5%) / 08450 (5%) / 08450 (5%)
Shelf Life: 3 years for BASE and 1 year (25°C/77°F) for CURING AGENT from time of production.*other shades according to assortment list.
Packaging: Available in 20 Litres

Related Products