International Intergard 1735

SKU
id18963
Part A: Non Hazardous, Part B: UN3066 (Class: 8, Pk Grp: II)
A high performance, low VOC, water borne two component epoxy with a high gloss finish for use on structural steel and concrete floors.
Available in 5 Litres. Tintable to many colours
From £179.50 £149.58
In stock
Only %1 left
Product Description

International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish for use on structural steel. Also suitable for application to concrete floors and walkways.

Best Uses

International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable. For use on structural steel and equipment in a range of aggressive environments including those found in chemical and petrochemical plants, pulp and paper mills and power stations in both new construction and industrial maintenance situations, under controlled conditions.

Also suitable for application to correctly prepared concrete floors and walkways.

Application

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Strict adherence to all cleanliness standards is essential for application of water based coatings.

Primed Surfaces
Intergard 1735 should always be applied over a recommended anti-corrosive coating scheme. The primer surface should be dry and free from all contamination and Intergard 1735 must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) or SSPC-SP6, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch primed prior to the application of Intergard 1735.

Plaster, Cement Render, Concrete etc.
Concrete should be cured for a minimum of 28 days prior to coating. The moisture content of the concrete should be below 6%. All surfaces should be clean, dry and free from curing compounds, release agents, trowelling compounds, surface hardeners, efflorescence, grease, oil, dirt, old coatings and loose or disintegrating concrete. All poured, and precast concrete must also be sweep blasted (preferred) or acid etched to remove laitence. The surface should be clean, dry and free from contamination. Remove old, loose or flaking paint. Fill and sand minor defects.

Damp patches, oil staining, bitumen bleed, nicotine deposits, efflorescence and rust discolouration must either be treated at source, or better, the cause of such stains/defects removed. Existing mould, algae and other growth must be killed before commencing work. Domestic strength bleach diluted 1:4 with water or a proprietary fungicide solution should be used. Two treatments may be necessary, after which the area must be washed down and scrubbed to remove residues. Ideally, to prevent future infestations the conditions which support growth should be identified and cure sought.

International Intergard 1735 is part of a wide range of International Paint products available from Promain.

Technical Details

Approvals

  • NATO Approval No. 8010-99-615-7042

Compatibility

The following primers are recommended for Intergard 1735:

Water borne

  • InterH2O 280
  • InterH2O 401

Solvent borne

Technical Info

Components: Two Part
Type: Water borne
Finish: High Gloss
Stock Colours: Just tints
Tintable: Yes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 66.0g per Litre
Volume Solids: 50%
Suitable Substrates: For steelwork and concrete floors / walkways
Application Method: Brush, Roller, Air Atomised Spray or Airless Spray
Theoretical Coverage: 10m2 per litre at 50 microns
Wet Film Thickness (WFT): 100 - 150 microns
Dry Film Thickness (DFT): 50 - 75 microns
Induction Time: -
Pot Life: 1 hour at 15°C
Touch Dry: 2 hours at 15°C
Overcoatable: 22 hours at 15°C
Hard Dry: 22 hours at 15°C
Cleaner / Thinner: Clean and Thin with either International GTA991 (or clean water)
Shelf Life: 12 months minimum at 25°C
Packaging: Available in 5 Litres

Related Products