International Intergard 251

SKU
id18897
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A two component epoxy anti-corrosive primer pigmented with zinc phosphate for anti corrosive protection.
Available in 20 Litres
From £264.76 £220.63
In stock
Only %1 left
Product Description

International Intergard 251 is a two component epoxy anti-corrosive primer pigmented with zinc phosphate for anti corrosive protection in the offshore, petrochemical and bridge industries.

Best Uses

International Intergard 251 is formulated for use on properly prepared surfaces in both new construction situations and as an industrial maintenance primer for a wide range of anti-corrosive coatings systems for use in the offshore, petrochemical, chemical, pulp and paper and bridge industries.

The fast drying and handling properties, together with extended overcoatability, make this an excellent primer for factory application prior to full system application on site. Intergard 251 provides good abrasion resistance which minimises mechanical damage in transit between the factory and site.

Intergard 251 is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions.

Application

Apply using air spray, airless spray, brush or roller. All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.

Abrasive Blast Cleaning
Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Intergard 251, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.
Surface profile must be a minimum of 50 microns (2 mils).

Shop Primed Steelwork
Weld seams and damaged areas should be cleaned to a minimum St3 (ISO 8501-1:2007) or SSPC-SP3. Optimum performance will be achieved with blasting to Sa2½ (ISO 8501-1:2007) or SSPC-SP6; where this is not practical, power tool preparation to SSPC-SP11 is recommended. If the shop primer shows extensive or widely scattered breakdown overall sweep blasting may be necessary.

International Intergard 251 is part of a wide range of International Paint products available from Promain.

Technical Details

Compatibility

Intergard 251 is designed for application to correctly prepared steel. However, it is also possible to apply over approved prefabrication primers. Further details of these can be obtained from our technical team.

The following primers are recommended for Intergard 251:

  • Interzinc 22 * (mist coat or tie coat may be required)
  • Interzinc 52
  • Interzinc 2280 * (mist coat or tie coat may be required)
  • InterH2O 280

The following topcoats are recommended for Intergard 251:

See relevant product data sheet for details.

Technical Info

Components: Two Part
Type: Zinc Phosphate Primer
Finish: Matt
Stock Colours: Grey, Red
Tintable: No
VOC Content: 293.0g per Litre
Volume Solids: 63%
Suitable Substrates: For steel
Application Method: Brush, Roller, Air Atomised Spray or Airless Spray
Theoretical Coverage: 8.4m2 per litre at 75 microns
Wet Film Thickness (WFT): 79 - 119 microns
Dry Film Thickness (DFT): 50 - 75 microns
Induction Time: -
Pot Life: 8 hours at 15°C
Touch Dry: 1 hour at 15°C
Overcoatable: Between 5 hours and 12 months at 15°C
Hard Dry: 5 hours at 15°C
Cleaner / Thinner: Thin if necessary with International GTA822. Clean all equipment immediately after use with International GTA822
Shelf Life: 12 months minimum at 25°C
Packaging: Available in 20 Litres

Related Products