International Intergard 269

SKU
id18977
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A quick drying two component epoxy primer for immersed or exposed conditions within a system.
Available in 20 Litres in Red
From £79.68 £66.40
In stock
Only %1 left
Product Description

International Intergard 269 is a quick drying two component epoxy primer for immersed or exposed conditions within a system.

Best Uses

International Intergard 269 is formulated as a blast holding primer suitable for use in immersed and exposed conditions and overcoatable with a wide range of high performance systems. For use at both new construction and maintenance.

Intergard 269 is also suitable for use as a tie coat on zinc silicate to prevent zinc salt formation on weathering and pinholing of subsequent high build topcoats.

Application

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.

Intergard 269 is suitable for use as a blast holding primer for steelwork intended for exposure in both immersed and atmospheric exposure conditions. Apply Intergard 269 at the recommended thickness as over-application will result in a glossy surface which may not be suitable for overcoating after ageing.

Abrasive Blast Cleaning

For immersion service, Intergard 269 must be applied to surfaces blast cleaned to Sa2½ (ISO 8501-1:2007) or SSPC-SP10. However, for atmospheric exposure Intergard 269 may be applied to surfaces prepared to a minimum of Sa2½ (ISO 8501-1:2007) or SSPC-SP6. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.

Ultra High Pressure Hydroblasting / (non-immersed service only)
May be applied to surfaces prepared to Sa2 (ISO 8501-1:2007) or SSPC-SP6 which have flash rusted to no worse than Grade HB2M (refer to International Hydroblasting Standards). Further information is available from International Protective Coatings.

Tie Coat Applications (see Product Characteristics)
In the case of zinc primers, where necessary, remove weld spatter, smooth weld seams and sharp edges and blast clean welds and damaged primer to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. The shop primer or other primer surface should be dry and free of all contamination (oil, grease, salt etc) and overcoated with Intergard 269 within the overcoating intervals specified for the primer (consult the relevant product data sheet). Ensure that the zinc primer has fully cured and is clean, dry and free from zinc salts prior to overcoating.

International Intergard 269 is part of a wide range of International Paint products available from Promain.

Technical Details

Approvals

  • NATO Approval No. 8010-99-983-0743
  • Norsok M-501 System 2A
  • Norsok M-501 System 2B
  • Norsok M-501 System 5A (Pre Qualified)
  • Norsok M-501 System 6A
  • Norsok M-501 System 8A

Compatibility

Intergard 269 is suitable for use over the following primers:

The following topcoats/intermediates are recommended for Intergard 269:

Technical Info

Components: Two Part
Type: Primer
Finish: Matt
Stock Colours: Red
Tintable: No
VOC Content: 293.0g per Litre
Volume Solids: 47%
Suitable Substrates: For metal in immersed or exposed conditions
Application Method: Brush, Roller, Air Atomised Spray or Airless Spray
Theoretical Coverage: 11.8m2 per litre at 40 microns
Wet Film Thickness (WFT): 85 microns
Dry Film Thickness (DFT): 40 microns
Induction Time: -
Pot Life: 12 hours at 15°C
Touch Dry: 35 minutes at 15°C
Overcoatable: 12 hours at 15°C
Hard Dry: 12 hours at 15°C
Cleaner / Thinner: Thinner: International GTA220 (or International GTA415). Clean all equipment immediately after use with International GTA822
Shelf Life: 12 months minimum at 25°C
Packaging: Available in 20 Litres

Related Products