*International Interplus 880

SKU
id18964
***
This product is now discontinued.
Out of stock
Product Description

Please note, this product is now discontinued. Contact our technical team for a suitable alternative.

International Interplus 880 is a low VOC, two component high solids flexible aliphatic surface tolerant polyurethane primer, intermediate or finish capable of producing high build films.

Best Uses

International Interplus 880 is primarily used as a high performance single coat industrial maintenance coating to upgrade any tightly adhering existing coating to a longer life durable system.

For use in a wide variety of aggressive environments, including those found in chemical plants, refineries, pulp and paper mills and on bridges. it is capable of providing superior gloss and colour retention particularly when compared to epoxy based finishes and will cure at temperatures down to -5°C (23°F). It may be applied to steel surfaces where it is not possible to abrasive blast.

Application

The performance of this product will depend upon the degree of surface preparation. The surface to be coated must be clean and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000.

Accumulated dirt and soluble salts must be removed. Dry bristle brushing will normally be adequate for accumulated dirt. Soluble salts should be removed by fresh water washing.

Abrasive Blast Cleaning
Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Interplus 880, the surface should be reblasted to the specified visual standard.

Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.

Power Tool Preparation
Power tool clean to a minimum St3 (ISO 8501-1:2007) or SSPC-SP3. Note, all scale must be removed and areas which cannot be prepared adequately by chipping or
needle gun should be spot blasted to a minimum standard of Sa2 (ISO 8501-1:2007) or SSPC-SP6. Typically this would apply to C or D grade rusting in this standard.

Aged Coatings
Interplus 880 is suitable for overcoating aged coatings which show good adhesion. Loose or flaking coatings should be removed back to a firm edge. Existing epoxy or polyurethane systems which are glossy may require abrasion to ensure good intercoat adhesion.

See Product Characteristics section for further details

Technical Details

Compatibility

Interplus 880 is suitable for overcoating all sound aged coatings but is not generally recommended for direct application to zinc silicate (e.g. Interzinc 22) or zinc epoxy (e.g. Interzinc 52).

The following primers are recommended for Interplus 880:

The following topcoats are recommended for Interplus 880:

It should be noted that Interplus 880 is not suitable for overcoating with thin films of alkyd, chlorinated rubber, vinyl or acrylic finishes.

For other suitable primers/topcoats consult our Technical Team.

Technical Info

Components: Two Components
Type: Surface Tolerant Polyurethane
Finish: Semi Gloss
Stock Colours: Wide range via the Chromascan system
Tintable: Yes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 190 g/lt
Volume Solids: 80% ± 3% (depends on colour)
Suitable Substrates: Steel Surfaces
Application Method: Brush, Roller, Airless Spray or Air Spray
Theoretical Coverage: 8 m²/litre at 100 microns d.f.t and stated volume solids
Wet Film Thickness (WFT): 94-156 microns
Dry Film Thickness (DFT): 75-125 microns
Induction Time: -
Pot Life: 2 hours at 15°C
Touch Dry: 90 minutes at 15°C
Overcoatable: After 3 hours at 15°C
Hard Dry: 3 hours at 15°C
Cleaner / Thinner: International GTA007
Shelf Life: 12 months minimum at 25°C (77°F). Subject to re-inspection thereafter
Packaging: Available in 20 Litres

Related Products