Sherwin Williams Firetex FX1003 SB Intumescent Coating White 20 Litres

SKU
ID12881
UN1263 (Class: 3, Pk Grp: III)
A single pack, thin film 120 minutes intumescent coating designed for site application via airless spray onto structural steel.
Available in 20 Litres
From £568.34 £473.62
In stock
Only %1 left
Product Description

Sherwin Williams Firetex FX1003 is a single pack, thin film 120 minutes intumescent coating designed for site application via airless spray onto structural steel.

Best Uses

FIRETEX FX1003 is designed for site application by airless spray, to provide fire resistance for up to 120 minutes on structural steel. After appropriate drying, FIRETEX FX1003 specifications can be exposed to the weather for up to 6 months provided that the specific use does not lead to ponding water due to rainfall, condensation or other site circumstances.

FIRETEX FX1003 can resist normal weather conditions for up to 6 months without topcoat provided it has had appropriate drying prior to exposure. Once an approved topcoat has been applied as appropriate to the prevailing conditions, then durability will be substantially enhanced. If the specific use or storage could lead to prolonged contact with water due to rainfall, condensation, or other site/transportation/storage circumstances, then a recommended topcoat must be used to prevent damage to the base coat.

Application

Recommended application via airless spray or brush. For certain dry, internal situations where the final colour / appearance is not critical, then FIRETEX FX1003 may remain un-topcoated. For externally exposed steelwork up to C4 and severe internal environments Acrolon C137V2 or Acrolon C237 must be used as a topcoat. For other internal environments where a topcoat is required then FIRETEX M71V2 or Sher-Cryl M770 should be used. In all instances for subsequent re-decoration, use FIRETEX M71V2, Sher-Cryl M770, Acrolon C137V2 or Acrolon C237 as appropriate.

FIRETEX FX1003 is designed for use over a suitably prepared and primed substrate. Ensure surfaces to be coated are clean, dry and free from all surface contamination. Under certain circumstances it may be possible to apply FIRETEX FX1003 directly to steel blast cleaned to a minimum standard of Sa2½ BS EN ISO 8501-1:2001, surface profile in the range 50-100 microns. FIRETEX FX1003 is capable of withstanding external exposure without topcoat providing:


The product is allowed to dry for at least 24 hours at 15°C in dry conditions with good air movement and ventilation. These conditions are based on a total dry film thickness of up to 800 microns. The drying time required will be increased if the film thickness is greater than 800 microns.
The substrate temperature is at least 3°C above the dew point at the time of application and during the drying period.

IMPORTANT INTUMESCENT PRODUCT NOTE: Always contact Promain’s technical team prior to purchase to obtain a tailored project specification and the advice necessary. The information displayed on this website should only be used as a guide. Promain UK Limited will not be held liable for any resulting damage to property, human life or monetary costs incurred due to incorrect specification, preparation, application or maintenance that has occurred due to negligence by either the purchaser or applicator. This includes your failure to have contacted us to obtain the relevant advice/specification.

Technical Details

Approvals:

  • Certifire Approved – Certificate CF5077
  • This product has been assessed in accordance with the Criteria of Acceptability given in the ASFP/BCF Industry Guidance Document
  • This product has been tested and assessed in accordance with the ASFP firetesting protocol for cellular beam protection. See Section 6.3 from ASFP Yellow Book 4th Edition

Technical Info

Components: Single Pack
Type: Solvent Based Intumescent
Finish: -
Stock Colours: White
Tintable: No
VOC Content: 286 gms/litre
Volume Solids: 75± 4%
Suitable Substrates: Structural Steel
Application Method: Brush, Airless Spray
Theoretical Coverage: See separate sheet of FX1003 loading requirements.
Wet Film Thickness (WFT): Spray: 1867 microns, Brush: 400 microns
Dry Film Thickness (DFT): Spray: 1400 microns, Brush: 300 microns
Induction Time: -
Pot Life: -
Touch Dry: 1 hour at 15°C
Overcoatable: 4 hours at 15°C
Fully Cured: -
Cleaner / Thinner: Cleanser / Thinner 2
Shelf Life: 2 years from date of production unopened or 'use by' date where specified.
Packaging: Available in 20 Litres

Related Products