International Interzone 954GF is a high solids, low VOC epoxy barrier coat, reinforced with chemically resistant high aspect ratio lamellar glass flake for enhanced durability, abrasion and corrosion protection with excellent cathodic disbondment performance.
International Interzone 954GF is suitable for the protection of steelwork in areas where high abrasion and corrosion resistance are required including splashzone and subsea areas of offshore structures, jetties, decks, bridges, chemical plants, pulp and paper mills, water treatment plants and underground pipework.
International Interzone 954GF has excellent resistance to cathodic disbondment, gives good compatibility with both sacrificial anode and impressed current systems, making Interzone 954GF particularly suitable for the long term protection of sub-sea structures. Can be used as part of a non-slip deck system in conjunction with appropriate aggregate.
The performance of this product will depend upon the degree of surface preparation. The surface to be coated must be clean and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Accumulated dirt and soluble salts must be removed. Dry bristle brushing will normally be adequate for accumulated dirt. Soluble salts should be removed by fresh water washing. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.
Abrasive Blast Cleaning
Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Interzone 954GF, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner. A surface profile of 50-75 microns (2-3 mils) is recommended.
Hand or Power Tool Preparation
Hand or power tool clean to a minimum St3 (ISO 8501-1:2007) or SSPC-SP3 for atmospheric use only. Note, all scale must be removed and areas which cannot be prepared adequately by chipping or needle gun should be spot blasted to a minimum standard of Sa2 (ISO 8501-1:2007) or SSPC-SP6. Typically this would apply to C or D grade rusting in this standard.
Ultra High Pressure Hydroblasting / Abrasive Wet Blasting
May be applied to surfaces prepared to Sa2 (ISO 8501-1:2007) or SSPC-SP6 which have flash rusted to no worse than Grade HB2M (refer to International Hydroblasting Standards). It is also possible to apply to damp surfaces in some circumstances. Further information is available from International Protective Coatings.
Interzone 954GF is suitable for overcoating some sound intact aged coatings. To ensure compatibility, application and evaluation of a test patch is required.
Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. Agitate Base (Part A) with a power agitator. Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.
nterzone 954GF will generally be applied to bare steel prepared by dry abrasive blasting, wet abrasive blasting or ultra high pressure hydroblasting.
The following primers are recommended for Interzone 954GF:
- Intercure 200
- Intergard 269 (for underwater use)
- Intercure 200HS
- Interline 982 (for underwater use)
- Intergard 251
- Interzinc 315
- Interzinc 52
- Interzone 1000
The following topcoats are recommended for Interzone 954GF:
|Stock Colours:||White, Black, RAL 1023, RAL 1004, Grey|
|Tintable:||Yes, to a limited colour range. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||145 g/L|
|Suitable Substrates:||For steelwork|
|Application Method:||Airless Spray, Air Spray, Brush, Roller|
|Theoretical Coverage:||1.70 m2 per litre at 500 microns DFT and stated volume solids|
|Wet Film Thickness (WFT):||235 - 588 microns|
|Dry Film Thickness (DFT):||200 - 500 microns|
|Pot Life:||60 minutes at 15°C|
|Touch Dry:||21 hours at 5°C|
|Overcoatable:||Between 40 hours and 21 days at 5°C|
|Hard Dry:||40 hours at 5°C|
|Cleaner / Thinner:||International GTA007 Maximum recommended thinning 5%|
|Shelf Life:||12 months minimum at 25°C (77°F). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of
heat and ignition.
|Packaging:||Available in 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.