International Interlac 665

SKU
ID20978
UN1263 (Class: 3, Pk Grp: III)
A single pack alkyd high gloss finish suitable as a easily maintained cosmetic finish coat on areas above the waterline.
Available in 20 Litres
From £302.72 £252.27
In stock
Only %1 left
Product Description

International Interlac 665 is a single pack alkyd high gloss finish suitable as a easily maintained cosmetic finish coat on areas above the waterline.

Best Uses

International Interlac 665 is ideal for use as an easily maintained cosmetic finish coat on areas above the waterline on marine boats and environments. It is also suitable for use on Newbuilding, Maintenance & Repair or On Board Maintenance.

Application

International Interlac 665 is suitable for application via Airless Spray, Brush, Conventional Spray or Roller.

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

Preparation: NEWBUILDING/MAJOR REFURBISHMENT
Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Interlac 665.

Preparation: REPAIR
Repair corroded areas with an appropriate International Paint primer (consult the primer data sheet).

Preparation: OBM
Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Interlac 665.

Interlac 665 may be applied directly over aged Interlac 665 following thorough fresh water washing and degreasing provided the coating to be overcoated is in an intact and tightly adherent condition. Loose or flaking coatings should be removed back to a firm edge and Interlac 665 or an appropriate primer should be used to repair the area before application of the full coat.

Consult our technical team for specific recommendations.

International Interlac 665 is part of a wide range of International Paint products from Promain.

Technical Details

Approvals & Certification

When used as part of an approved scheme, this material has the following certification:

  • Fire Resistance - Surface Spread of Flame (Exova Warringtonfire)
  • Fire Resistance - Surface Spread of Flame (Korean Register of Shipping)
  • Fire Resistance - Smoke & Toxicity (Exova Warringtonfire)
  • Fire Resistance - Marine Equipment Directive compliant
  • Food Contact - Carriage of Grain (NOHA)
  • Meets Petrobras Standard N-2492 - Alkyd Finish Gloss

Systems & Compatibility

Interlac 665 should only be applied over recommended anticorrosive primers. The primer to be used will depend upon vessel area, existing coatings, coating condition and application location. Typical primers include:

  • Interprime 198
  • Intertuf 203
  • Interprime 128 (in Europe)
  • Interprime 538 (in Europe)
  • Interlac 497 (applied as a sympathetically coloured undercoat over Interprime 198)

Technical Info

Components: Single Pack
Type: Alkyd
Finish: High Gloss
Stock Colours: CLB000-White, CLD260-Intl. Orange, CLK724-Storm Grey, CLL274-Red, CLL549-Signal Green, CLY999-Black
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 420 g/L
Volume Solids: 48%
Suitable Substrates:  
Application Method: Airless Spray, Brush, Conventional Spray, Roller
Theoretical Coverage: 12 m2 per litre at 40 microns DFT, allow appropriate loss factors
Wet Film Thickness (WFT): 83 microns
Dry Film Thickness (DFT): 40 microns
Induction Time: -
Pot Life: -
Touch Dry: 14 hours at 10°C
Overcoatable: 24 hours at 10°C
Hard Dry: 48 hours at 10°C
Cleaner / Thinner: International GTA004. Thinning is not normally required
Shelf Life: 24 months minimum at 25°C. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition
Packaging: Available in 20 Litres

Related Products