*Hempel Hempadur Quattro XO 17770

SKU
ID19324
***
This product is now discontinued. See PPG Sigmacover 350 as a potential alternative.
In stock
Product Description

Please note, this product is now discontinued. See PPG Sigmacover 350 as a potential alternative.

Hempel Hempadur Quattro XO 17770 is a two-component, abrasion resistant, pure epoxy universal primer with excellent anti-corrosive properties. The product is available with different levels of Aluminium and Fibre pigmentation to deliver tailor made optimised performance properties for different harsh service conditions.

Best Uses

Hempel Hempadur Quattro XO 17770 is best used as a universal pure epoxy and self-primed high performance coating system for atmospheric or in water service, including water ballast tanks to be coated according to IMO-PSPC requirements defined in the IMO Resolution MSC.215(82)). HEMPADUR QUATTRO XO 17770 is intended for all year application down to -10°C/14°F and for applications where fast recoating and handling is required.

Application

New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G). Apply immediately after cleaning. All damage of shop primer and contamination from storage and fabrication should be thoroughly
cleaned prior to over-coating. For repair and touch-up use: HEMPADUR QUATTRO XO 17770.

Ballast tanks: For PSPC type approved coating, consult separate application instructions.

Steel, maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to St 3 (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the performance of the paint. As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat must appear with roughened surface
after the water jetting. By water jetting to steel, cleanliness shall be Wa 2 - Wa 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). A flash-rust degree of maximum M (atmospheric exposure), preferably L (immersion) (ISO 8501-4:2006) is acceptable before application. Feather edges to sound and intact paint. Dust off residues. Touch up to full film thickness. On pit corroded surfaces, excessive amounts of salt residues may call for water jetting or wet abrasive blasting, alternatively dry abrasive blasting followed by high pressure fresh water hosing, drying, and finally, dry abrasive blasting again.

Other substrates: Contact Promain's Technical Team

Use only where application and curing can proceed at temperatures above: -10°C/14°F. Apply only on a dry and clean surface with a temperature min. 3°C/5°F above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying.

Technical Details

Certificates and Approvals

  • PSPC type approved. (Consult HEMPEL for specific Type Approval Certificates)
  • Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain.
  • Norsok M-501 system no. 1 (Pre-Qualified)
  • Norsok M-501 system no. 3B (Pre-Qualified)

Features

  • Excellent anti-corrosive and very good mechanical properties.
  • Available with Aluminium and Fibre pigmentation.
  • Short drying time.
  • Curing down to -10°C/14°F.

Technical Info

Components: Two Component
Type: Pure epoxy universal primer
Finish: Semi-Flat
Stock Colours: Grey 16480
Tintable: Yes, other shades according to assortment list. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 272 g/l [2.3 lbs/US gallon]
Volume Solids: 72 ±2%
Suitable Substrates: Steel
Application Method: Airless spray / Brush / Roller
Theoretical Coverage: 5.8 m2/l [232.6 sq.ft./US gallon] - 125 micron/5 mils
Wet Film Thickness (WFT): 175 micron [7 mils]
Dry Film Thickness (DFT): 125 micron [5 mils]
Induction Time: To facilitate proper application properties it is recommended to allow the thoroughly mixed base and curing agent  to prereact before application
Pot Life: 2 hour(s) 20°C/68°F
Surface Dry: 1.5 hour(s) 20°C/68°F
Overcoatable: After minimum 1.5 hours at 20°C - See product Data Sheet for full details
Fully Cured: 5 day(s) 20°C/68°F
Cleaner / Thinner: Thinner: 08450, Clean tools with: Hempel Tool Cleaner 99610
Shelf Life: 3 years for base and 2 years (25°C/77°F) for curing agent from time of production
Packaging: Available in 20 Litres

Related Products