Jotun Barrier 80

SKU
ID17003
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: Non Hazardous
A fast drying, anti corrosive, high solids 2 part polyamide cured zinc rich epoxy coating.
Available in Grey in 9 Litres
£285.77 £238.14
In stock
Product Description

Jotun Barrier 80 is a fast drying, anti-corrosive, high solids 2 part polyamide cured zinc rich epoxy coating. Contains high zinc dust, designed for severe corrosive environments.

BBA HAPAS Certified for the corrosion protection of structural steelwork in highway applications.

BBA Approval Logo

Best Uses

Jotun Barrier 80 is ideal for structural steel and piping exposed to a wide range of corrosive atmospheric environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Suitable for carbon steel, repair of inorganic zinc silicate coating and damaged galvanised substrates.

The product conforms to the compositional requirements of SSPC paint 20, level 2 and ISO 12944 and the zinc pigments comply with ASTM D520 type II zinc dust. Specially designed as a primer in coating systems where extended durability is required. Suitable for exterior exposure in offshore environment, below 120°C.

Application

When preparing new surfaces, maintaining already coated surfaces or aged coatings it is necessary to remove all contamination that can interfere with coating adhesion, and prepare a sound substrate for the subsequent product. Inspect the surface for hydrocarbon and other contamination and if present, remove with an alkaline detergent. Agitate the surface to activate the cleaner, and before it dries, wash the treated area using fresh water. Paint solvents (thinners) shall not be used for general degreasing or preparation of the surface for painting due to the risk of spreading dissolved hydrocarbon contamination.

Paint thinners can be used to treat small localized areas of contamination such as marks from marker pens. Use clean, white cotton cloths that are turned and replaced often. Do not bundle used solvent saturated cloths. Place used cloths into water. When the surface is an existing coating, verify with technical data sheet and application guide of the involved products, both over coatability and the given maximum over coating interval. New surfaces should be cleaned to a minimum of SA2.5. When applicable, products primarily meant for use as primers or anti-fouling may have slight colour variations from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

A zinc epoxy should be applied in a smooth and even film. Too rough film could give risk of popping when the subsequent coat is applied. Film thickness exceeding recommended maximum may cause mud cracking and poor film integrity. Sufficient ventilation is very important to ensure proper drying/curing of the film. Refer to data sheets for application guide.

Technical Details

Approvals

  • Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1
  • BBA HAPAS Certified for the corrosion protection of structural steelwork in highway applications
  • Highway Approval HA Item No 109
Components: Two Part
Type: Polyamide cured zinc rich epoxy coating
Finish: Matt
Stock Colours: Grey
Tintable: No
VOC Content: 366.0g per litre
Volume Solids: 61%
Suitable Substrates: Carbon steel, repair of inorganic zinc silicate coating and damaged galvanised steel substrates
Application Method: Airless Spray or Brush
Theoretical Coverage: 15.3 - 6.8m2 per litre
Wet Film Thickness (WFT): 65 - 150 microns
Dry Film Thickness (DFT): 40 - 90 microns
Induction Time: 30 mins at 23°C
Pot Life: 12 hours at 23°C
Touch Dry: 20 mins at 10°C
Overcoatable: 2 hours minimum at 10°C
Fully Cured: 7 days at 10°C
Cleaner / Thinner: Jotun Thinner No. 17
Shelf Life: 24 months
Packaging: Available in 9 Litres