International Intergard 1735

SKU id18963 Part A: Non Hazardous, Part B: UN3066 (Class: 8, Pk Grp: II)
A high performance, low VOC, water borne two component epoxy with a high gloss finish for use on structural steel and concrete floors.
Available in 5 Litres. Tintable to many colours
£79.00 (£94.80 Inc VAT)
*These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.
£79.00 (£94.80 Inc VAT)

Product Description

International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish for use on structural steel. Also suitable for application to concrete floors and walkways.

Best Uses

International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable. For use on structural steel and equipment in a range of aggressive environments including those found in chemical and petrochemical plants, pulp and paper mills and power stations in both new construction and industrial maintenance situations, under controlled conditions.

Also suitable for application to correctly prepared concrete floors and walkways.

Application

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Strict adherence to all cleanliness standards is essential for application of water based coatings.

Primed Surfaces
Intergard 1735 should always be applied over a recommended anti-corrosive coating scheme. The primer surface should be dry and free from all contamination and Intergard 1735 must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) or SSPC-SP6, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch primed prior to the application of Intergard 1735.

Plaster, Cement Render, Concrete etc.
Concrete should be cured for a minimum of 28 days prior to coating. The moisture content of the concrete should be below 6%. All surfaces should be clean, dry and free from curing compounds, release agents, trowelling compounds, surface hardeners, efflorescence, grease, oil, dirt, old coatings and loose or disintegrating concrete. All poured and precast concrete must also be sweep blasted (preferred) or acid etched to remove laitence. Surface should be clean, dry and free from contamination. Remove old, loose or flaking paint. Fill and sand minor defects.

Damp patches, oil staining, bitumen bleed, nicotine deposits, efflorescence and rust discolouration must either be treated at source, or better, the cause of such stains/defects removed. Existing mould, algae and other growth must be killed before commencing work. Domestic strength bleach diluted 1:4 with water or a proprietary fungicide solution should be used. Two treatments may be necessary, after which the area must be washed down and scrubbed to remove residues. Ideally, to prevent future infestations the conditions which support growth should be identified and cure sought.

Recommended Products To Use


International Interzinc 52

International Interzinc 52

A two component, anti-corrosive metallic zinc rich epoxy primer.

£341.00 (£409.20 Inc VAT)
International Interseal 670HS

International Interseal 670HS

For use on a wide variety of substrates including hand prepared rusty steel.

£99.00 (£118.80 Inc VAT)
International Intercure 200

International Intercure 200

A two component epoxy zinc phosphate / micaceous iron oxide primer suitable for low temperature overcoating.

£273.00 (£327.60 Inc VAT)
International Intergard 251

International Intergard 251

A two component epoxy anti-corrosive primer pigmented with zinc phosphate for anti corrosive protection.

£224.00 (£268.80 Inc VAT)
International Intergard 475HS

International Intergard 475HS

A low VOC, high solids, high build, two component epoxy coating.

£339.00 (£406.80 Inc VAT)
International Interzinc 42

International Interzinc 42

A two component, metallic zinc primer for steel in aggressive environments.

£341.00 (£409.20 Inc VAT)
International Intergard 269

International Intergard 269

A quick drying two component epoxy primer for immersed or exposed conditions within a system.

£44.00 (£52.80 Inc VAT)