PPG SigmaCover 400 / Amerlock 400

SKU
ID3835
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN3469 (Class: 3.8, Pk Grp: III)
A self-priming coating for steel and concrete. Formerly PPG SigmaCover 640 / Amerlock 400C.
Available in 4 and 20 Litres. Please contact us regarding other colours.
From £72.00 £60.00
In stock
Only %1 left
Product Description

PPG SigmaCover 400 (Amerlock 400) is a two component high solids epoxy coating suitable for garage floors, walkways and other concrete and metal substrates.

Formerly PPG SigmaCover 640/Amerlock 400C.

PPG SigmaCover 400 (Amerlock 400) is a high performance, two-pack epoxy paint coating which is suitable for concrete and metal floors as well metal pipes and structural steel. Formerly known as SigmaCover 640, SigmaCover 400 is a self-priming, universal epoxy paint which has good adhesion to most coatings. SigmaCover 400 is available in a choice of BS and RAL colours, with a semi-gloss finish.

Best Uses

PPG SigmaCover 400 (Amerlock 400) has been specifically manufactured as a professional coating. With its unique formula, it is highly suitable for use on bridges, tank exteriors, containers and oil tanks. Additionally, PPG SigmaCover 400 is ideal for chemical acid and fuel bunds.

Application

When applying to carbon steel, blast clean substrate to Sa2.5. When being used for immersion also blast clean to Sa2.5. For concrete and masonry, remove grease, oil and other contamination. For galvanized steel, remove all oil and contaminations with a suitable detergent or cleaner. Lightly abrasive blast to 40 - 75 microns. For ferrous metals and stainless steel, remove all rust, dirt grease and moisture. Lightly blast clean to a profile of 40 - 100 microns.

Ensure substrate temperature is kept within 5 and 50°C. Mix both components prior to combining. Mix hardener within base container by mechanical means. Can be thinned between 0 - 10% with suitable PPG thinners, especially during cold conditions such as garage floors during winter. Porous substrates such as screeded floors or tampered concrete floors can often use far more epoxy floor paint from our experience we estimate a coverage rate of approximately 3m2 per litre per coat.

PPG SigmaCover 400 should be applied by spray, brush or roller.

Surface and Environment

PPG SigmaCover 400 can be used in commercial, construction and industrial environments where chemical spillages, splashes and fumes from acids, alkalis, solvents and water can cause damage to the surface. PPG SigmaCover 400 works by protecting steel and concrete substrates from these examples of chemical and atmospheric attack. Because of its high resistance to weathering, SigmaCover 400 is perfect for application to exterior bund linings, including, chemical, fuel or specially selected acid bunds.

PPG SigmaCover 400 can be applied over mechanically cleaned steel and is also suitable for use on concrete or prepared damp surfaces.

Technical Details

Features

  • Formerly Amerlock 400C and Croda Mebopro by Ameron
  • High performance coating
  • Resistant to acids, alkalis, solvents and fresh and salt water spillage/splashes
  • Formerly SigmaCover 640
  • Suitable for bund linings
  • For surfaces such as concrete we calculate approx. 6m2 per litre
  • Can be thinned between 0 - 10% with suitable PPG thinners, especially during cold conditions such as garage floors during winter. Porous substrates such as screeded floors or tampered concrete floors can often use far more epoxy floor paint from our experience we estimate a coverage rate of approximately 3m2 per litre per coat.

Technical Info

Components: Two Part
Type: Solvent Based
Finish: Semi Gloss
Stock Colours: White, Black, MIO
Tintable: Yes, upon request. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 180.0g per Litre
Volume Solids: 85%
Suitable Substrates: For carbon steel, concrete, masonry, galvanized steel, non ferrous metals, stainless steel, aged coatings and repairs
Application Method: Brush, Roller or Airless Spray
Theoretical Coverage: 8.5 m2 per litre at 100 microns
Wet Film Thickness (WFT):  
Dry Film Thickness (DFT): 100 - 200 microns
Induction Time: -
Pot Life: 2 hours at 20°C
Touch Dry: 6 hours at 20°C
Overcoatable: After 16 hours at 20°C. See overcoating tables on datasheet
Fully Cured:  
Cleaner / Thinner: Thin with PPG Thinner 91-92. PPG Thinner 21-06, PPG Thinner 21-25
Shelf Life: At least 36 months when stored cool and dry
Packaging: Available in 4 and 20 Litres

Related Products