Remmers MB 2K

SKU
id17862
Non Hazardous
For the rapid waterproofing of building elements as well as containers, tanks and reservoirs, both indoors and outdoors.
Available in 25 Kg
£181.70 £151.42
In stock
Product Description

Remmers MB 2K - Multi-Tight 2K - Flexible, polymer thick coating, combining the properties of flexible and crack-bridging mineral waterproofing grouts (MWG) and bitumen-thick coatings (PMBC).

Best Uses

Remmers MB 2K is used for the rapid waterproofing of building elements as well as containers, tanks and reservoirs, both indoors and outdoors. In addition it is also used for:

  • Waterproofing in new buildings
  • WTA-compliant retroactive waterproofing
  • Approved for connecting to water impermeable concrete structures
  • Waterproofing of plinths and base points
  • Waterproofing in a bond
  • Bonding layer on old bitumen coatings
  • Repair of flat roof waterproofing on roofs of structures which are not habitations
  • Horizontal waterproofing in and underneath walls
  • For attaching perimeter insulation panels

Application

Horizontal waterproofing in and underneath walls
Apply the material in two layers on the previously prepared substrate. The second layer is applied once the first layer can no longer be damaged when worked over.

Vertical surface waterproofing
Apply the material in two layers on the previously prepared substrate. The second layer is applied once the first layer can no longer be damaged when worked over.

Horizontal surface waterproofing
Apply the material in two layers on the previously prepared substrate. The second layer is applied once the first layer can no longer be damaged when worked over. After the waterproofing has dried thoroughly, place two layers of PE sheet over the waterproofing before the screed is laid. At the edges, the waterproofing layer is applied up to the upper edge of the floor or up to the horizontal barrier.

Pipes passing through walls
Seal passing-through pipes by using the product to form a cove around them.

Technical Details

Notes

  • Water pressure tight
  • High tensile adhesion strength
  • Highly flexible, elastic and crack-bridging
  • Can be covered after a very short time (≥ 4h)
  • UV-resistant
  • Resistant to frost and de-icing salt
  • Can be plastered and painted over
  • Can be applied as a grout, with a brush or trowel, or by spraying

Technical Info

Components: Two Component Set
Type: Solvent Free, Bitumen Free
Finish: -
Stock Colours: -
Tintable: No
VOC Content: -
Volume Solids: -
Suitable Substrates: Building Elements, Containers, Tanks, Reservoirs
Application Method: Brush, Trowel, Scraper, Roller or Spray
Theoretical Coverage: At least 1.2 kg/m²/mm of dry coat thickness
Wet Coat Thickness: The maximum total wet coat thickness must not exceed 5 mm
Dry Film Thickness (DFT): -
Application Conditions:  Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C.
Working Time:  30-60 minutes at 20°C
Touch Dry: -
Overcoatable: After 4 hours, work can be continued with adhesive mortar, filling mortar or reinforcement mortar.
Fully Cured: days at 20°C
Cleaner / Thinner: Clean tools with water before mortar sets
Shelf Life: 9 months unopened if kept in a cool, dry place protected from frost
Packaging: Available in 25 Kg
Product Video

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use