Res-Tec Flexitec 2020 Chopped Strand Matting Fibreglass 225g/m2 CSM

SKU id20926 Non Hazardous
Provides a smooth, tough finish for the Res-Tec 2020 System. Liquid applied roofing system for felt, concrete, asphalt, GRP and timber.
Available in 15m2 or 30m2 sizes
£30.50 (£36.60 Inc VAT)
£30.50 (£36.60 Inc VAT)

Product Description

Res-Tec 2020 Chopped Strand Matting Fibreglass 225g/m2 CSM provides a smooth, tough finish for the Res-Tec 2020 System. Allows for an even application of the resin.

Best Uses

The Flexitec 2020 System by Res-Tec is a flexible, single resin GRP system with full overlay and new deck capabilities. Combining the best elements of fibreglass with the versatility of overlay systems, no other flat roof solution performs at this level across so many applications.

Best Uses

Similar to fibreglass systems, Res-Tec Flexitec 2020 System is reinforced with fibreglass CSM for extra strength and crack resistance. The finished membrane is extremely tough, impact resistant and can easily accommodate foot traffic. Due to its unique flexible technology, Res-Tec Flexitec 2020 System is able to coat all common roof surfaces. This includes felt, concrete, asphalt, GRP and timber. This means roofs can be overlaid without the need for strip and replace works. No matter the size, shape or complexity of the roof, Res-Tec Flexitec 2020 provides a seamless, tough and flexible membrane to any roof or balcony area.

  • Excellent crack resistance and water resistant properties
  • Can in many cases be applied over the existing roof membrane without the need to remove and re-board
  • Overcoatable: Tolerant of short completion delays and easily repairable
  • Lower odours that alternative roofing systems
  • All year round fast curing
  • Rapid wetting of the glass fibres and early conforming to detail work. Can be applied using only a fluffy roller.
  • Prevents drainage / sagging from vertical surfaces

Application

It is important that fibreglass CSM reinforcement is stored in dry conditions. Before use, inspect the mat to ensure there are no damaged, defective or wet areas present. Carefully measure the roof and assess how many strips of mat are needed, while allowing a 50mm overlap on each width of the mat. Carefully remove the mat from its polythene bag and lay on a clean dry surface. Roll out the required length - if possible always working with the fall of the roof (matting strips running perpendicular to the fall of the roof to avoid holding water).

Cut with a straight edge and a very sharp Stanley type knife, taking care to protect the roof deck or surface below. Re-roll the cut piece and store in a clean, dry place. Cut all you need for the roof before you start mixing the resin. The matting has one straight cut edge and one feathered (torn) edge. When overlapping rolls of mat, a feathered edge should go over a straight edge. The overlap must not be less than 50mm otherwise a weak spot will be created.

See application guide download for full in depth details. Available via the above technical tab.

Recommended Products To Use


Res-Tec Flexitec 2020 Resin

Res-Tec Flexitec 2020 Resin

Resin for Res-Tec Flexitec 2020 Liquid Roofing. Liquid applied roofing system for felt, concrete, asphalt, GRP and timber.

£83.00 (£99.60 Inc VAT)
Res-Tec Flexitec 2020 Powder Additive

Res-Tec Flexitec 2020 Powder Additive

Designed to be added to Res-Tec Flexitec 2020 Primer & Resin to initiate the curing process.

£31.00 (£37.20 Inc VAT)
Res-Tec Flexitec 2020 Primer

Res-Tec Flexitec 2020 Primer

Flexitec 2020 Primer is recommended for all porous, bituminous, cementitious, timber and PVC single ply substrates.

£87.50 (£105.00 Inc VAT)