Rustoleum 8700 Hygienic Wall Coating Mould-Resistant Paint

Non Hazardous
A low solvent mould-resistant hygienic coating for walls & ceilings in breweries, cellars and areas of high humidity.
Available in 5 Litres in Pure White (RAL 9010)
£127.93 £106.61
In stock
Product Description

Rustoleum 8700 Hygienic Topcoat is a water-based single pack hygienic topcoat protects against normal humidity and contamination indoors. Suitable for walls and ceilings.

Rustoleum 8700 Hygienic Topcoat offers users a highly durable glossy white finish, and can be ordered in other colours by special request.

Best Uses

Rustoleum 8700 Hygienic Topcoat is developed to be applied on mineral surfaces primed with White Masonry Sealer 8798 or directly on previous coated substrates. 8700 will resist normal humidity and should be applied over 8798 in humid conditions.

  • Offers better protection against contamination than non-hygienic paint
  • Very fast drying and recoating times (3 coats in a day)
  • Approved for direct food contact (R1)
  • Can be applied on damp surfaces in combination with 8798 hygienic primer
  • Durable gloss finish


Rustoleum 8700 Hygienic Topcoat should be applied using brush, roller or spray and offers a theoretical coverage rate of 10m2 per litre to produce a white glossy finish.

Surface and Environment

Rustoleum 8700 Hygienic Topcoat is designed for use in areas exposed to high humidity and moisturous areas where mould and mildew has or is likely to build up. Rustoleum 8700 Hygienic Topcoat can be applied to damp, walls and ceilings where there is a high possibility that mould will appear. Remove contamination with FK111 Cleaning Solution. Wash total surface with plenty of fresh/warm water or high pressure (steam) cleaning in order to remove all remnants of contamination and cleaners. Prime or spot-prime with 8798 hygienic primer. The surface must be clean during application. (may be slightly damp)

Technical Details


  • Single pack water based hygienic coating
  • Very low solvent content
  • Rustoleum Mathys 8700 contains fungicides that are not removed by washing
  • Practically odourless during application
  • Very fast drying and recoating times (3 coats in a day)
  • Can be applied with damp surfaces (White Masonry Sealer 8798)

Technical Info

Components: One Part
Type: Water Based
Finish: Gloss
Stock Colours: RAL 9010 Pure White
Tintable: No
VOC Content: 87.0g per Litre
Volume Solids: 35%
Suitable Substrates: For mineral surfaces primed with White Masonry Sealer 8798 or directly on previous coated substrates
Application Method: Brush, Roller, Air Atomised Spray or Airless Spray
Theoretical Coverage: 10 m2 per litre
Wet Film Thickness (WFT): 100 microns
Dry Film Thickness (DFT): 35 microns
Induction Time: -
Pot Life: -
Touch Dry: 30 minutes at 20°C
Overcoatable: After 2 hours at 20°C
Fully Cured: 3 days at 20°C
Cleaner / Thinner: Water
Shelf Life: 5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C. Keep from freezing
Packaging: Available in 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use