Please note, this product is now discontinued. See Sikafloor Level 30 or Sika Schonox FPL+ as potential alternatives.
Sika Sikafloor 100 Level is a polymer modified cementitious floor levelling compound for 1-10mm depths. Suitable for interior floors.
Sika Sikafloor®-100 Level is suitable for filling, smoothing and levelling of the suitable substrates before applying textile and elastic floor coverings in interior areas.
Sikafloor 100 Level benefits from very low emission as a cement based self-levelling compound suitable for interior areas. Sikafloor®-100 Level is characterised by good working properties. Suitable for castor chair rollers according to EN 12 529.
- For interior use
- Can be ground
- Water proof against dispersion adhesives
- Self levelling
- Very smooth application
- Suitable for application on subfloor heating systems
- Layer-thickness 1-10 mm
- Can be pumped
- Feather-edging acceptable in pedestrian areas
- Suitable for castor wheels loading with layer-thickness more than 1 mm according to EN 12 529
- Polymer modified
- Low tension
- Standard Sikafloor EP primers give excellent bonding to the Sikafloor Level products
SUBSTRATE QUALITY / PRE-TREATMENT
Adequate strength, load bearing capacity, dimensional stability and permanent dryness. Substrate must be free of residues which reduce adhesion, e.g. dust, dirt, oil, fat and loose particles. Separation layers, sinter layers, and other similar contamination should be removed through appropriate measures, such as sanding, brushing, abrasive blast cleaning, milling or thorough cleaning. Old, loose and weak levelling layers should be removed mechanically.
With subsequent installation of floor coverings, cement screeds are required to display a residual moisture reading of ≤ 2.0 CM-% (heating screeds ≤ 1.8 CM-%), calcium sulphate screeds should have a reading of ≤ 0.5 CM-% (heating screeds ≤ 0.3 CM-%).
Layers of water-soluble adhesives, e.g. sulphite waste- adhesives, are to be mechanically removed. Remaining adhesive residues should be primed with Sika Epoxy Primer (for example Sika Primer MB). Old water-resistant adhesives are to be mechanically removed as thoroughly as possible.
Rooms in buildings without a basement, are to be sealed against rising dampness in compliance with the standard.
For 25.0 kg Sikafloor®-100 Level approx. 6.0 l water. Add Sikafloor®-100 Level to cold clean water to form a homogeneous mixture using a clean receptacle. Use of
a mixer with disc stirring rod is recommended. After a short waiting time, mix again thoroughly.
After mixing pour out the levelling compound and spread using a smoothing trowel. Even surfaces are easily achieved with a suitable notched trowel. In the case of higher layer-thickness, contact with vertical structures should be avoided by putting in a perimeter isolating strip.
Carry out preparatory work - such as filling joints, evening out hollows and unevenness - using a suitable Sika repair mortar. For normal absorbent substrates such as cement screeds, rapid cement screeds, concrete prime with Sikafloor®-01 Primer (1:3) or Sikafloor®-03 Primer.
For calcium sulphate substrates such as calcium sulphate screeds prime with Sikafloor®-03 Primer (drying time 60 minutes) or Sikafloor®-01 Primer (1:1) / (drying time at least 24 hours). For old water resistant adhesive residues, prime with Sikafloor®-01 Primer (neat).
|Suitable Substrates:||Interior Floors|
|Theoretical Coverage:||Approx. 1.5 Kg per m2 per mm|
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Pot Life:||Approx. 30 minutes at 20 °C|
|Surface Dry:||Ready for foot traffic after approx. 3 hours.|
|Overcoatable:||Sikafloor®-100 Level can be overcoated as follow:
|Cleaner / Thinner:||Immediately after use clean tools with water.|
|Shelf Life:||6 months from the date of production. Opened bags should be closed immediately and used up as soon as possible. Do not store below +5°C.|
|Packaging:||Available in 25 Kg|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.