Sikafloor®-262 AS N Thixo may only be used by experienced professionals. Sikafloor®-262 AS N Thixo is used as a decorative and protective electrostatic conductive
textured coating for concrete or cement screeds with normal up to medium heavy wear. Suitable as a wearing course in industries, such as automotive, electronics and pharmaceutical manufacturing, storage facilities and warehouses.
Particularly suitable for areas with sensitive electronic equipment e.g. CNC machinery, computer rooms, aircraft maintenance sheds, battery-charging rooms and areas subjected to high explosion risks etc.
The concrete substrate must be sound and of sufficient compressive strength (minimum 25 N/mm²) with a minimum pull off strength of 1.5 N/mm². The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. If in doubt apply a test area first.
Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured
surface. Weak concrete must be removed and surface defects such as blow holes and voids must be fully exposed. Repairs to the substrate, filling of blow holes / voids and surface levelling must be carried out using appropriate products from the Sikafloor®, SikaDur® and SikaGard ® range of materials. The concrete or screed substrate has to be primed or levelled in order to achieve an even surface. Unevenness influences the film thickness and thus the conductivity. High spots must be removed by e.g. grinding. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush and/or vacuum.
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 3 minutes until a uniform mix has been achieved. To
ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimize air entrainment.
Sikafloor®-262 AS N Thixo must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
Sikafloor®-262 AS N Thixo (unfilled) is applied with a serrated trowel for textured wearing layer e.g. Trowel No. 999 or Adhesive Spreader No.777, Toothed blades
No. 23 = A3’ and then back-rolled (crosswise) with a textured roller.
Sika Sikafloor 262 AS N Thixo is used within the following Sika systems:
See Data Sheets tab for System sheet downloadable PDF.
|Type:||Coloured Thixotropic Resin|
RAL 7032, 7035, 7037
Under direct sun light there may be some discolouration and colour variation. This has no influence on the function and performance of the coating.
|Tintable:||Other colours are available on request|
|VOC Content:||500.0g per Litre|
|Suitable Substrates:||For concrete|
|Application Method:||Textured Roller|
|Theoretical Coverage:||0.5 - 0.8 Kg per m2|
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Pot Life:||25 minutes at 20°C|
|Overcoatable:||Before applying Sikafloor®-264 N Thixo on Sikafloor®-156/-161 /-160 allow between 12 hours and 2 days at 20°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||Clean all tools and application equipment with Sika Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.|
|Shelf Life:||24 months from date of production|
|Packaging:||Available in 26 Kg|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.