Teknos Nordica Eko

Non Hazardous
A water-borne wooden cladding paint based on double-action acrylate for wooden surfaces externally.
Available in 2.7 and 9 Litres
From £34.26 £28.55
In stock
Only %1 left
Product Description

Teknos Nordica Eko is a water-borne double-action acrylate for wooden surfaces such as cladding externally. Offers a glossy and hard surface that is dirt-repellent. Retains its colour and gloss for a very long time.

Best Uses

Teknos Nordica Eko is ideal for new and previously painted wooden surfaces externally such as exterior wooden walls, fascia boards, weather boards and window boards. If you need a product for log structures we would recommend Teknos Woodex Aqua Classic wood stain.

This product is suitable for application over external composite cladding boards if a priming coat of Teknos Nordica Primer is used.


Treat the surface as soon as possible. At least the impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt, dust and mildew. If needed, use Teknos Rensa Facade facade cleaner. Apply a coat of clear Teknos Woodex Aqua Base priming oil. Allow to dry for one day.

Prime wooden surfaces with 5-10% diluted Teknos Nordica Primer and allow the surfaces to dry for 1 - 3 days depending on the weather. Clean rusty steel parts: by sanding, wire brushing eg., and prime with Teknos Ferrex Aqua anti-corrosive paint.

Replace deteriorated wooden parts with new ones. Remove loose matter, dirt and dust. Remove the deteriorated paint coats entirely. Note, that the adherence of an old thick paint layer to the substrate may have been weakened, therefore the paint should be removed although the paint film looks intact. The old paint layer is removed primarily by scraping or wire brushing and possibly by heating the surface with infra-red heater designed for that purpose. Secondarily paint remover or blasting can be used.

Wash surfaces with Teknos Rensa Facade facade cleaner and rinse thoroughly. Old, untreated wooden surfaces can before the priming be treated with clear Teknos Woodex Aqua Base priming oil, see 'NEW WOODEN SURFACE'. Prime bare wooden surfaces with Teknos Nordica Primer, diluted 5-10%. Allow to dry for 1 to 3 days depending on the weather. Clean rusty steel parts: by sanding, wire brushing eg., and prime with Teknos Ferrex Aqua anti-corrosive paint.

Technical Details
Components: One Part
Type: Water Borne
Finish: Gloss
Stock Colours: Just tints
Tintable: Yes, to Teknos Exterior Colours and RAL / BS shades. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 130.0g per Litre
Volume Solids: 37%
Suitable Substrates: For external vertical wood
Application Method: Brush or Spray
Theoretical Coverage: 5 - 8 m2 per litre
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: -
Pot Life: -
Touch Dry: 1 hour at 23°C
Overcoatable: 4 hours at 23°C
Fully Cured:
Cleaner / Thinner: Water
Shelf Life:
Packaging: Available in 0.9, 2.7 and 9 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Related Products