Teknos Woodex Aqua Solid

SKU
id17898
Non Hazardous
A water-borne, acrylate/alkyd based solid wood stain for outdoor use.
Available in 2.7 and 9 Litres
From £27.59 £22.99
In stock
Only %1 left
Product Description

Teknos Woodex Aqua Solid is a water-borne, acrylate/alkyd based solid wood stain for outdoor use. Suitable for use on new and press-impregnated wood.

As used on the Beach Huts at Marine Walk Folkestone Kent.

Best Uses

Teknos Woodex Aqua Solid is to be used for renewed treatment of old, faded wood stain surfaces, and also when a uniform colour is desired on old and new wood stain surfaces. Suitable also for use on new and press-impregnated wood. Typical uses are garden offices, garden buildings, cladding, covering boards, fences, window frames, etc.

For log surfaces we recommend Teknos Woodex transparent wood stains.

  • Tintable to over thousand colours
  • Film forming

Application

NEW WOODEN SURFACE:
Treat the wooden surface which is subjected to weather strain as soon as possible. At least the pre-treatments, impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt and dust. Wash dirty and/or mildewed surfaces with Teknos Rensa Façade Cleaner. Brush the detergent into the surface and leave it to take effect as long as possible. However, the surface must not get to dry. After this rinse the surface thoroughly with clean water and allow to dry completely. Treat the wooden surface with clear Teknos Woodex Aqua Base priming oil. Allow to dry for one day. Apply by spray or brush. Treat end grain especially carefully. The surface treated with priming oil is then primed with Teknos Woodex Aqua Solid diluted abt. 10 % by volume. Allow to dry for abt. 12 h. Apply by brush. When spray painting, finish the wet painted surface with a brush.

In order to achieve the most long-lasting treatment also Teknos Nordica Primer can be used for priming. Drying time is 1–3 day depending on the temperature and humidity of the air. Treat end grain especially carefully.

PREVIOUSLY PAINTED/WITH PRIMING OIL TREATED OR OLD WOODEN SURFACE:
Replace or repair wooden parts that are in poor condition. Remove loose matter, loose or poorly adherent paint or priming oil as well as greyed or fluffy layers of wood by e.g. scraping, wire brushing or using an infra-red heater. Avoid unnecessary damaging of the wooden surface. The adhesion of an old, thick paint layer to the substrate may have been weakened so much that the paint should be removed even if it seems intact. Wash surfaces with Teknos Rensa Façade Cleaner. Brush the detergent into the surface and leave it to take effect as long as possible. However, the surface must not get to dry.

After this rinse the surface thoroughly with clean water and allow to dry completely. Avoid unnecessary wetting of the wooden structures during the washing. Bare wooden surface of the damaged parts are treated withTeknos Woodex Aqua Base. Allow to dry for 1 day. After that prime the damaged parts with Teknos Woodex Aqua Solid diluted abt. 10 % by volume. Allow to dry for abt. 12 h.

Technical Details
Components: One Part
Type: Water Based
Finish: Semi Matt
Stock Colours: See above Colourcard. Translucent colours depend on below wood colour / texture
Tintable: Yes, upon request. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 130.0g per Litre
Volume Solids: 40%
Suitable Substrates: For external wood
Application Method: Brush, Roller
Theoretical Coverage:
  • Sawn Timber: 5 - 8 m2 per litre
  • Palned Timber: 8 - 10 m2 per litre
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Induction Time: -
Pot Life: -
Touch Dry:
Overcoatable: After 12 hours at 23°C
Fully Cured:
Cleaner / Thinner: Water
Shelf Life: 2 years unopened in original packaging
Packaging: Available in 2.7 and 9 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use