Owatrol D1 Pro is a solvent-based, saturating wood oil, offering long-term protection and UV resistance to interior and exterior wooden substrates, including, hardwood, softwood, and some tropical hardwoods, such as ipe, teak, bangkirai and mahogany.
Owatrol D1 Pro is a solvent-based, saturating wood oil, offering long-term protection and UV resistance when applied to interior and exterior wooden substrates. D1 Pro is available in a Honey Gold colour to help reduce the effects of UV degradation that causes the timber to become grey over time
Owatrol D1 Pro is extremely versatile and can be applied to a variety of different appliances, including garden furniture, fences, cladding, floors, stairs, doors, door frames, window frames, and decking, to name a few. Owatrol D1 Pro offers excellent penetration for a long lasting natural finish.
Surfaces must be clean, dry and free of dirt, grease, grime, mildew and previous coatings. Treat mildew with a 50/50 bleach/water solution. Scrub solution on to surface and allow to stand for 10-15 minutes; rinse thoroughly. After cleaning, allow wood to dry 2-3 good drying days or until it has reached a moisture content of 18 % or less before applying Owatrol D1 Pro.
Owatrol D1 Pro may only be applied to bare wood surfaces or a weathered wood surface that was previously finished with Owatrol D1 Pro. ALL other finishes must be completely and thoroughly removed. If necessary sand surface after cleaning and/or stripping (80 grit paper).
New wood surfaces:
New wood surfaces have a hard shiny surface called mill-glaze that prevents maximum penetration and adhesion of any finish, this should be removed to ensure maximum performance the finish. Treat with Owatrol Aquanett or Owatrol Prepdeck and neutralise with Owatrol Net-Trol.
Weathered wood surfaces (untreated):
Wood that has weathered longer than 12 months or turned grey should be cleaned with Owatrol Net-Trol to remove all loose wood fibres, dirt and other surface contaminants. If wood is severely contaminated, clean with Owatrol Prepdeck or Owatrol Aquanett and neutralise with Owatrol Net-Trol.
Previously coated surfaces (paint, stain, varnish...):
All previous coatings must be completely and thoroughly removed with Owatrol Dilunett, Owatrol Prepdeck or Owatrol CDKP 90.
Solvent (oil or alkyd based finishes): Strip with Owatrol Dilunett neutralise with Owatrol Net-Trol.
Acrylic finishes - Water-based: Strip with Owatrol Prepdeck neutralise with Owatrol Net-Trol.
Other finishes i.e. 2 pack epoxies, urethanes… Strip with Owatrol CDKP 90.
Note: Hardwoods inc’ exotic hardwoods and woods rich in tannins i.e. Oak, Chestnut, Teak, Ipe, Bangkarai… may darken with Owatrol Aquanett, Owatrol Prepdeck or Owatrol Dilunett, neutralising with Owatrol Net-Trol immediately after rinsing will lighten and restore the woods colour.
Thoroughly remove any existing coatings with Owatrol CDKP 90 or by mechanical abrasion. Sand surface with 80 or 100 grit paper to open the woods’ pores.
Dust off and wash with Methylated Spirits (Denatured Alcohol), Acetone or similar (NOT White Spirit) to degrease the surface. Allow to dry.
Surface and Environment
Owatrol D1 Pro can be applied to a number of surfaces including, hardwood, softwood, and some tropical hardwoods, such as ipe, teak, bangkirai and mahogany. With non drip properties, Owatrol D1 Pro can be applied to vertical surfaces as well as horizontal.
- Can be used on horizontal or vertical surfaces
- High UV resistance
- Honey Gold tint to reduce UV degradation
- Ideal for dense, greasy or difficult to impregnate hardwood
- Long lasting natural finish
- Excellent penetration
- Non film building. Must be in the wood not on the surface
- Suitable for interior and exterior application
- Mildew resistant finish
- Easy to use
- Easy to maintain (no stripping, no sanding)
- Allows local touch up
- Tropical hardwoods such as Ipe, Teak, Bangkirai, Mahogany
- Exterior woodwork Decking, Garden Furniture, Fences, Cladding
- Interior wooden surfaces such as Floors, Stairs, Door & Window Frames
- Horizontal & Vertical Surfaces
|Type:||Solvent Based Wood Oil|
|Stock Colours:||Clear, Honey Gold|
|VOC Content:||628 grams per litre|
|Suitable Substrates:||For interior and exterior wood|
|Application Method:||Brush, Roller, Airless Spray or HVLP|
|Theoretical Coverage:||Initial: 1 to 4 m2 per litre
Maintenance: 8 to 12 m2 per litre
Actual coverage will vary depending on application method, type, texture, age and porosity of the wood.
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Surface Dry:||24 hours at 20°C|
|Cleaner / Thinner:||Clean all tools and equipment with white spirit whilst still wet. If allowed to dry remove with paint stripper.
Any rags etc soaked in D.1 PRO may spontaneously catch fire if improperly discarded. Rags etc must be saturated with water
or placed in a sealed water filled container and disposed of according to local regulations.
|Shelf Life:||5 years in original unopened packaging. Left over D.1 PRO should be transferred to a smaller, airtight, closed metal or glass container. Keep from freezing and high temperatures.|
|Packaging:||Available in 5 and 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.