Teknos Helo Aqua is a single pack, polyurethane, water-borne special varnish based on polyurethane dispersion. For wooden surfaces indoors and outdoors. Available in 20%, 40% and 80% gloss levels.
Teknos Helo Aqua is ideal for the treatment and protection of internal wooden floors, parquet flooring, wooden stairs, stair balustrade wooden furniture such as tables or chairs and wooden toys. Suitable for sponge, spray or brush application.
- Suitable for use on children's toys
- Suitable for interior and exterior use
Available in 3 sheen levels:
- Teknos Helo Aqua 20 - 20% Gloss (Semi Matt) - Recommended for wooden stair tread application
- Teknos Helo Aqua 40 - 40% Gloss (Semi Gloss)
- Teknos Helo Aqua 80 - 80% Gloss (Gloss)
The wooden surface must be dry, carefully sanded and cleaned from dust and other impurities. Stir Teknos Helo Aqua well both before use and between the applications, but be careful not to let air into the varnish.
Untreated parquets and wooden plank floors:
Prime with 15% diluted HELO AQUA 80 using brush, trowel or roller. Finish with 2 - 3 coats of HELO AQUA 20 using brush or trowel. Spread out the varnish in the direction of the pattern and the grain of the wood.
Previously varnished floors:
It is recommended that the surfaces are sanded to bare wood and that the instructions above for untreated parquet and wooden plank floors are followed. If the old varnished coat is in good condition HELO AQUA 20 varnish can be applied according to the instructions for finishing to a surface that has been carefully sanded
(sanding paper no. 150 or finer). In this case, however, the varnish is first to be tested on a small area to ensure proper adhesion.
Stairs and furniture:
Brush application is recommended for stairs and furniture. Prime with HELO AQUA 80, if needed. Apply first a thin coat of HELO AQUA 20 varnish and let it dry for at least one hour. Sand the surface and remove all sanding dust carefully. Apply a second coat of varnish and let dry for about 3 hours before applying the third coat.
- The product has been classified to Group M1 in Emission Classification of building materials
- Product meets the requirements of Toy Safety Directive 2009/48/EC for limit values for migration of chemical elements
|Type:||Water Based Polyurethane|
|Finish:||Available in 20%, 40% and 80% Gloss levels|
|Tintable:||Yes, to Teknos Internal Wood Shades and RAL, BS Shades. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||140.0g per Litre|
|Suitable Substrates:||For internal and external wood|
|Application Method:||Brush, Roller, Sponge or Trowel|
|Wet Film Thickness (WFT):||-|
|Dry Film Thickness (DFT):||-|
|Touch Dry:||1 - 3 hours at 20°C|
|Overcoatable:||After 1 - 3 hours at 20°C|
|Fully Cured:||1 - 2 weeks at 20°C|
|Cleaner / Thinner:||Water|
|Shelf Life:||2 years unopened in original packaging|
|Packaging:||Available in 2.7 and 9 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.