Sherwin Williams Nova-Plate UHS Epoxy Tank Lining

SKU
id12875
Part A: UN3082 (Class: 9, Pk Grp: III), Part B: UN3066 (Class: 8, Pk Grp: II)
An ultra high solids epoxy novolac amine engineered specifically for immersion service in storage tanks.
Available in 20 Litres
From £1,211.76 £1,009.80
In stock
Only %1 left
Product Description

Sherwin Williams Nova-Plate UHS is an ultra high solids epoxy novolac amine engineered specifically for immersion service in storage tanks.

Best Uses

Sherwin Williams Nova-Plate UHS is recommended specifically for immersion service in ballast tanks, oil tanks, refined fuel storage tanks and for well deck overheads. The high build, edge retentive properties of Nova-Plate UHS provide superior protection compared to conventional epoxies.

Benefits include Nova-Plate UHS being low VOC, low odour, with a fast cure hardener available. For use over prepared steel or concrete in industrial and marine exposures such as Meets MIL-PRF-23236, Type VII, Class 5, 7, 13, 19, Grade C, Ballast tank interiors, Well deck overheads, Oil storage tank interiors, Refined fuel storage tank interiors, Acceptable for use under thermal insulation, CHT Tanks and containment areas.

Suitable for use in the Mining & Minerals Industry, NORSOK system 7C approval.

Application

Clean up using no13. Prepare steel to BS EN ISO8501-1:2007 Sa2½, SSPCSP10, NACE2. Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion. Can be applied onto iron and steel, concrete and masonry. Apply using plural component airless spray, airless spray, or brush and roller for stripe coating and repair. Refer to data sheet for full information.

Technical Details

Approvals:

  • Meets MIL-PRF-23236, Type VII, Class 5, 7, 13, 19, Grade C
  • Norsok M-501 System 3F
  • Norsok M-501 System 3G
  • Norsok M-501 System 7C (Pre Qualified)

Technical Info:

Components: Two Pack
Type: Epoxy
Finish: Gloss
Stock Colours: Light Grey, White
Tintable: No
VOC Content: <100 g/L
Volume Solids: 98% ± 2%, mixed
Suitable Substrates: Steel
Application Method: Airless Spray, Plural Component Airless Spray, Brush, Roller
Theoretical Coverage: 2.5m2/L (1 coat over primer)
Wet Film Thickness (WFT): Max 400 microns (1 coat over primer)
Dry Film Thickness (DFT): Max 400 microns (1 coat over primer)
Induction Time: None required
Pot Life: 40 minutes at 25°C (with standard hardener)
Touch Dry: 4 hours at 25°C (with standard hardener)
Overcoatable: Minimum 14 hours at 25°C, Maximum 21 days at 25°C (with standard hardener)
Cure to Service: 5 days at 25°C °(with standard hardener)
Cleaner / Thinner: Thinning not recommended. Clean up with Thinner 13
Shelf Life: 2 years from date of production unopened or 'use by' date where specified
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use