International Interplate 398

SKU
id21050
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN1263 (Class: 3, Pk Grp: II)
A two component, fast drying modified epoxy phosphate prefabrication primer for manual or automatic spray application.
Available in 20 Litres
From £206.50 £172.08
In stock
Only %1 left
Product Description

International Interplate 398 is a two component, fast drying modified epoxy phosphate prefabrication primer for manual or automatic spray application.

Best Uses

International Interplate 398 is ideal to pre-prime steel prior to the fabrication process. International Interplate 398 can be overcoated with a large range of coating systems which are suitable for use in a wide spectrum of environments ranging from water immersion, aggressive coastal to rural situations.

Application

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Where necessary, remove weld spatter and smooth weld seams and sharp edges. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.

Abrasive Blast Cleaning
Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Interplate 398, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.
This product is NOT recommended over hand prepared steel.

Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. Agitate Base (Part A) with a power agitator. Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.

Technical Details

Compatibility

Interplate 398 can be overcoated with a number of systems suitable for steel protection in a wide range of environments.
The following products can be applied directly to Interplate 398:

Technical Info

Components: Two Pack
Type: Modified Epoxy Phosphate Prefab Primer
Finish: Matt
Stock Colours: Red, Grey
Tintable: No
VOC Content: 617 g/L
Volume Solids: 25%
Suitable Substrates: For steel
Application Method: Airless Spray, Air Spray, Brush, Roller
Theoretical Coverage:
  • 10 m2 per litre at 25 microns DFT and stated volume solids
  • 401 sq.ft  per US gallon at 1 mils DFT and stated volume solids
Wet Film Thickness (WFT): 100 microns
Dry Film Thickness (DFT): 25 microns
Induction Time: -
Pot Life: 16 hours at 15°C
Touch Dry: 4 minutes at 15°C
Overcoatable: After 12 hours at 15°C
Hard Dry: 4 minutes at 15°C
Cleaner / Thinner: International GTA803
Shelf Life: 6 months minimum at 25°C (77°F). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of
heat and ignition.
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use