Protecta-Kote Accelerator

SKU
id17523
UN1760 (Class: 8, Pk Grp: III)
A pure, solvent free catalyst used to speed up the drying time of Protecta-kote non-slip and smooth coatings.
Available in 20ml for 1 Litre Protecta-Kote and 80ml for 4 Litres Protecta-Kote
From £11.99 £9.99
In stock
Only %1 left
Product Description

Protecta-Kote Accelerator is a pure, solvent free catalyst used to speed up the drying time of Protecta-Kote non-slip and smooth coatings. Not suitable for Protecta-Kote UVR.

Best Uses

Protectakote Accelerator is a second component that can be added to Protecta-Kote coatings to speed up the drying time. This is ideal when applying Protecta-Kote in Winter. Protectakote Accelerator should only be added where time constraints exist and temperatures are lower than 15°C.

Protectakote Accelerator may reduce the glossiness of the application especially when the humidity is high.

  • Pre-weighed – just add and stir in
  • Long pot life: accelerated product can be kept for 24-48 hours before thickening occurs
  • Fast drying - Drying times can be reduced to as little as one hour
  • Low humidity and low temperature effects which extend drying times can be reduced
  • Lead & heavy metal free
  • Suitable for all colours of Protectakote

Application

Protectakote Accelerator should be added to the product just prior to use and stirred in well. Put the lid back on until you are ready to apply the coating.

Protecta-Kote Accelerator is supplied in preweighed doses suitable for either 1 litre packs or for 4 litre packs. The product is supplied in a 20ml dose for addition to a
litre, or an 80ml dose for addition to a 4 litre pack.

In rare cases two doses may be added- when humidity and/or temperature is very low. The active catalyst in a 20ml dose is 3g of DBTDL, while an 80ml dose contains 12g of DBTDL. A 20ml (or 80ml) dose is a 2% addition by volume. The percentage addition of active accelerator is 0.3% by mass per dose.

Please note, this product is not suitable for Protecta-Kote UVR. Addition of Protectakote UVR Accelerator to regular Protectakote will cause lumps to form immediately and render the product useless.

Technical Details
Components: One Part
Type: Additive
Finish: -
Stock Colours:
Tintable:
VOC Content: -
Volume Solids: -
Suitable Substrates: -
Application Method: Use with Protecta-Kote Rubber Anti-Slip Paint only
Theoretical Coverage: -
Wet Film Thickness (WFT): 330 microns
Dry Film Thickness (DFT): -
Induction Time: -
Pot Life: -
Touch Dry: -
Overcoatable: -
Fully Cured:

With One Dose: 4 hours 30 mins at 10°C

With Two Doses: 3 hours 45 mins at 10°C

Cleaner / Thinner: -
Shelf Life: 2 years unopened in original packaging
Packaging: Available in 20ml and 80ml

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use