Bradite Floor-It DP9

SKU
id22972
Non Hazardous
A high-performance, ambient cross-linking, water based acrylic floor paint that benefits from being recoatable after 1 hour.
Available in 2.5 and 5 Litres. Tintable to RAL and BS Shades
From £45.60 £38.00
In stock
Product Description

Bradite Floor-It DP9 is a high-performance, ambient cross-linking, water based acrylic floor paint that benefits from being recoatable after 1 hour.

Best Uses

Bradite Floor-It DP9 is formulated for coating interior /exterior bare or previously painted suitably prepared concrete, wood, steel, tarmac asphalt floors. Floor It will give your interior and exterior floors an economical, hard wearing, flexible floor coating with good chemical and excellent water resistance.

This product can also be used with Bradite Low Slip Additive LS30 to provide additional under foot traction.

Bradite Floor-It DP9 is suitable for use in domestic and light commercial garages. In the first seven days after application, vehicles should be left outside to allow tyres to cool down (especially after long journeys) to help prevent hot tyre pick up. Spills of petrol and diesel should be cleaned up as soon as possible to reduce the danger of slip and to prevent discolouration of the floor paint. Brake fluid is highly aggressive and will attack most floor paints on contact – use drip/capture pans when working on brake systems to prevent permanent damage to the floor paint finish.

Application

Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Powder Coated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details.

High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil. Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.

Brush and Roller - Supplied ready for use. Thin, if required, with up to 5% water.
Conventional Air Spraying - Thin with 5-15% Water as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately.
Airless Spraying - Thin with 0 – 10% water as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

For application on concrete, wood or other absorbent substrates, the first coat should be thinned 5-10% water to allow penetration into the substrate.

  • 1st coat Bradite Floor-It DP9 (thinned)
  • 2nd coat Bradite Floor-It DP9
  • 3rd coat Bradite Floor-It DP9

For maintenance painting the 1st coat will be a touch up to bare areas only.

While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20°C and should not be subject to heavy traffic for at least 48 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity.

Technical Details

Certificates and Approvals

  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.

Technical Info

Components: Single Pack
Type: Water Based
Finish: Semi Gloss (approx. 35%)
Stock Colours: Light Grey and Dark Grey
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 101 g/L
Volume Solids: 38.59%
Suitable Substrates: For internal/external wood, tarmac, asphalt, steel, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared and primed. Suitably prepared and well adhered existing coatings including, polyurethane, epoxy and chlorinated rubber. External floor surfaces should be above local water table and/or have intact DPM barrier present. Compatibility with existing coatings should be confirmed by preparing and painting a test patch.
Application Method: Brush, Roller, Conventional or Airless Spray
Theoretical Coverage:

12 m2 per litre per coat

2 full coats on bare absorbent surfaces, apply a 20% thinned priming coat first)

Wet Film Thickness (WFT): 100 microns / coat
Dry Film Thickness (DFT): 39 microns / coat
Induction Time: -
Pot Life: -
Surface Dry: 30 minutes at 20°C
Overcoatable: After 1 hour minimum at 20°C
Fully Cured: 7 days at 20°C
Cleaner / Thinner: Water
Shelf Life: 12 months minimum in original unopened containers.
Packaging: Available in 2.5 and 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use