Bradite One Can is a single pack, quick drying, low odour, water thinned primer/finish coat, with excellent adhesion, stain blocking and anti-corrosive properties. It can be tinted to most BS and RAL colours.
Bradite ONE CAN is for use as a quick drying adhesion promoting, stain blocking and anti-corrosive coating on ferrous metals, non ferrous metals, common plastics (e.g. melamine and uPVC), ceramic tiles, glass, wood and existing painted surfaces.
All surfaces must be dry and dust free before coating. Application should always conform with the codes of practice described in BS 6150 and BS 5493.
Aluminium, stainless steel, galvanised steel, copper and other metals: Cleaned and degreased, and lightly abraded if possible. White salts on weathered galvanising must be removed during cleaning and degreasing. Light surface rusting can be treated with Bradite Rust Converter RC46. Heavy rusting to be removed to clean metallic finish (SIS-St 3).
New Wood: Ensure moisture content of the timber is below 15% before commencing application. Damp wood should never be painted as this may give rise to blistering, flaking, cracking and premature coating failure.
Green Oak: Should not be painted unless it has been weathered for at least 6 months.
Existing paint finish: Remove all loose and flaking paintwork. Degrease using Bradite TD39 Industrial Degreaser, followed by clean water rinse. Rub down thoroughly with a medium grade sand paper to provide a key and a defect free smooth surface, “feathering in” areas where paint has been removed.
Plastics: For long term performance, clean & lightly sand down surfaces.
New plaster walls: For plaster skim, allow at least four weeks for the plaster to thoroughly dry. Apply a primer coat by thinning the paint with a 5 to 25% (v/v) addition of clean water, depending upon the porosity of the substrate. Cut in by brushing at the same dilution recommendation as for priming, to promote flow and sealing of the substrate.
For new, fully plastered walls, allow at least six months for the plaster to thoroughly dry before painting.
This product is not recommended for painting lime or other natural plasters.
|Finish:||Eggshell (approx. 25%)|
|Stock Colours:||Black and White|
|Tintable:||Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||30 g/L|
|Suitable Substrates:||Plaster Work, Hardwoods, Softwoods, Concrete, Aluminium, Stainless Steel, Powder Coatings, PVCu Windows, Doors etc.|
|Application Method:||Brush, Roller or Airless Spray|
|Theoretical Coverage:||12 m2/L/coat|
|Wet Film Thickness (WFT):||75 - 100 microns/coat|
|Dry Film Thickness (DFT):||35 microns per/coat|
|Surface Dry:||30 minutes at 20°C|
|Overcoatable:||After 1 hour minimum at 23°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||Water|
|Shelf Life:||2 years minimum in original unopened containers.|
|Packaging:||Available in 1, 2.5 and 5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.