Centrecoat MMA Freezer Grade Colour Coat

SKU
id23642
Part A: UN1866 (Class: 3, Pk Grp: II), Part B: UN3106 (Class: 5.2)
A fast curing, low temperature coating for industrial freezers, cold stores and refrigerators, curing to -20°C.
Available in 5 Kg. Tintable to RAL and BS shades upon request.
From £101.96 £84.97
In stock
Only %1 left
Product Description

MMA Freezer Grade Colour Coat is a two pack, fast curing, low temperature coating, curing down to -20°C. Providing a seamless floor finish, it is used in industrial freezers, ice rinks and cold temperature storage and refrigerators.

Best Uses

Centrecoat MMA FG (Freezer Grade) Colour Coat allows curing down to -20°C so is ideal for industrial freezers, ice rinks and cold environments as part of a system. The inherent slip resistance of the coating may be enhanced by the incorporation of a suitable anti-slip dressing aggregate.

  • Tough and abrasion resistant
  • Colour Stable
  • Very good chemical resistance
  • Rapid curing minimises down times
  • Suitable in wet areas
  • Hygienic and easily cleaned
  • Cures at low temperatures
  • Hot water and fat resistant to 80°C

Centrecoat MMA FG Colour Coat is formulated as an abrasion and chemical resistant floor coating suitable for cold rooms such as refrigeration chambers, cold chambers, cooler chambers, restaurant cold storage, food cold rooms, industrial freezers, restaurant freezers, cold temperature storage, refrigerators in commercial premises and commercial beverage coolers.

Application

Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc. Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. Centrecoat MMA FG Pourable Repair Mortar. Suitable mechanical treatment, such as vacuum grit blasting, is the preferred treatment prior to application as this ensures a mechanical ‘key’ which will optimise adhesion.

Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish Standard. All dust shall be removed prior to coating application. A coat of Centrecoat MMA FG Primer may be required. Check data sheet.

Centrecoat MMA FG Colour Coat is supplied as a two pack material consisting of the BASE component, and the CATALYST component,. Incorporate the CATALYST component into the BASE component under mechanical stirring, and mix for 1-2 minutes.

Apply Centrecoat MMA FG Colour Coat using short nap perlon, or smooth lambswool rollers at a nominal rate of 0.30kg/m². Following a minimum of 1 hour apply a second coat at the same nominal rate. Should a slip resistant or skid resistant finish be required then broadcast an appropriate aggregate onto the first coat within 10 minutes of application. Following a minimum of 1 hour, sweep off excess aggregate and apply a second coat of Centrecoat MMA FG Colour Coat.

Clean equipment with Centrecoat MMA Tool Cleaner immediately after use.

Technical Details
Components: Two Pack
Type: MMA
Finish:
Stock Colours: Grey and Red
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content:
Volume Solids:
Suitable Substrates: For freezer grade concrete and steel
Application Method: Short nap perlon, or smooth lambswool rollers
Theoretical Coverage: A 5 Kg pack is sufficient to cover an area of 8.3m2 with the recommended two coat treatment, providing a minimum thickness of 500 microns.
Wet Film Thickness (WFT):
Dry Film Thickness (DFT): 500 microns minimum
Induction Time: -
Pot Life: 15 - 20 minutes at 20°C
Light Foot Traffic: 1 hour at 20°C
Vehicle Traffic: 2 hours at 20°C
Full Chemical Resistance: 24 hours at 20°C
Cleaner / Thinner: Clean equipment with Centrecoat MMA Tool Cleaner immediately after use.
Shelf Life: Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C.  Adequate ventilation of the storage area should be provided. Keep container tightly closed when not in use Centrecoat MMA FG Colour Coat has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions.
Packaging: Available in 5 Kg

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use