£7.75 delivery on orders excluding certain products & postcodes *

Sales & Technical 01462 421 333
Search
My Cart

FLAG Acid Etch Solution

SKU
id10281
UN1789 (Class: 8, Pk Grp: III)
A pre-treatment for concrete power floated or very smooth concrete floors to aid adhesion.
Available in 5 Litres
£22.30 £18.58
In stock
main product photo
Product Description

FLAG Acid Etch Solution is a blended pre-treatment for concrete power floated or very smooth concrete floors that is applied to create a good key before applying single or two pack floor paints.

Best Uses

FLAG Acid Etch Solution has been expertly blended to provide a pre-treatment for concrete power floated or very smooth concrete floors that is applied to create a good key before applying single or two pack floor paints. FLAG Acid Etch Solution is a water based solution that helps open the pores of the concrete and prepares the surface to accept its next treatment be it a paint coating or a floor sealer. Power floated floors are extremely smooth and floor paints have difficulty in adhering to the surface, following a treatment with FLAG Acid Etch the surface has a slight texture to the surface, this texture provides a good key for the paint to stick to.

Application

When applying Acid Etch to a floor you will notice the solution will fizz this is the acid reacting with the concrete, the Acid Etch needs to be applied until this fizzing stops. After application of Acid Etch to a floor the floor will need to be rinsed with clean water to wash the acid etch away and allowed to completely dry before the floor paint is applied. This is especially essential when applying solvent based floor paints or line marking but when applying water based floor paint it is not as critical. When calculating the amount of product required we would suggest you base your calculations on approximately 20m2 per litre.

Technical Details
  • FLAG Acid Etch Solution can be applied to interior and exterior floors
  • For use on power floated and concrete flooring
  • Finish: N/A
  • Volume solids: N/A
  • Flash point: N/A
  • Specific gravity: 1.1
  • Dry to touch: 2 - 4 hours at 20 degrees C.
  • Overcoating time: 1 - 2 days
  • Application by soft brush, mop or broom
  • Use water to clean up
  • Theoretical spreading rate: Approx 20 m2 per litre
  • Available in 5 Litres.
Components: One Part
Type: Acid Etch
Finish: -
Stock Colours: Clear
Tintable: No
VOC Content: -
Volume Solids: -
Suitable Substrates: For concrete power floated or very smooth concrete floors
Application Method: Brush / Mop / Broom
Theoretical Coverage: Approx. 20 sq. metres per litre
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Induction Time: -
Pot Life: -
Touch Dry: 2 - 4 hours at 20°C
Overcoatable: After 1 - 2 hours at 20°C
Fully Cured: -
Cleaner / Thinner: Water
Shelf Life: 2 years unopened
Packaging: Available in 5 Litres
Product Data Sheet (37.67 kB)
Safety Data Sheet (42.38 kB)

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use