£9.95 delivery on orders excluding certain products & postcodes *
Hempel Pro-Filler 35370
SKU
ID23889
Part A: UN3077 (Class: 9, Pk Grp: III), Part B: UN3259 (Class: 8, Pk Grp: II)
A two component, lightweight epoxy filler for boat hulls.
Available in 5 Litres in 49500 Light Green
From
£159.74
£133.12
In stock
Only %1 left
Product Description
Hempel's Pro-Filler 35370 is a two component, lightweight epoxy filler. Features high adhesion and water resistance. Easy to sand upon curing.
Best Uses
Hempel Pro Filler 35370 is suitable as a filler and fairing compound, and is especially suitable for profiling large areas and detailed fairing where structural strength is important. It can be used on most primed rigid substrates, above and below the waterline in marine environments.
- Complete hull profiling
- Minimum weight when profiling the surface
- Minimum shrinkage during drying
- Optimises man-hours
Hempel's Pro Filler 35370 be applied in coats up to 10-12 mm for a uniform, smooth film build.
Application
Remove oil, grease and other contaminants by suitable detergent cleaning. Clean with Hempel's Pre-Clean.
New build:
For uncoated surfaces, sand and remove all dust. Prime with 1 - 2 coats of specified Hempel's Primer.
Maintenance and Repair:
Previously coated surface: Abrade, clean and dry the surface. Sand to smoothen filler.
Immediately before use, mix equal parts of each of the two components until a uniform colour is obtained. Avoid air bubbles in the mixture. Clean up with Hempel's Thinner 08451 and / or Hempel's Degreaser 99611. The product can be applied in a thickness up to 12 mm. Fair the product whilst it is still possible to make finger prints in the filler. Overcoat when dry with 2 coats of recommended Hempel's Primer. Topcoat finishes should not be applied directly on top of the product.
Technical Details
| Components: | Two Pack |
| Type: | Epoxy Filler |
| Finish: | Semi Gloss |
| Stock Colours: | 49500 Light Green |
| Tintable: | No |
| VOC Content: | 57 g/L |
| Volume Solids: | 100% |
| Suitable Substrates: | Hulls |
| Application Method: | Putty knife |
| Theoretical Coverage: | 0.5m2 per litre |
| Wet Film Thickness (WFT): | 2000 microns |
| Dry Film Thickness (DFT): | 2000 microns |
| Induction Time: | - |
| Pot Life: | 45 minutes at 20°C |
| Touch Dry: | 6 hours at 20°C |
| Overcoatable: | Dependent on primer - see data sheet |
| Fully Cured: | - |
| Cleaner / Thinner: | Hempel's Thinner 845 08451 / Hempel's Degreaser 99611 |
| Shelf Life: | Base 24 months, and curing agent 36 months at 25°C |
| Packaging: | Available in 1, 2.5 and 5 Litres |
Product Video
Related Products
Teknos Teknofill 5001-00 Acrylate Filler
An aqueous product for spot filling of primed interior and exterior wood such as windows and doors.
From
£9.46
£7.88
Rustoleum Mathys Mur-Filler
An elastic joint filler based on water dispersed high polymers.
From
£143.39
£119.49
Sherwin Williams Firetex M72 Intumescent Filler
A solvent based intumescent mastic coating. For the repair of small areas of damage to Sherwin Williams Firetex range.
From
£67.08
£55.90
Teknos Aqua Filler 1100 Opaque Internal Primer
A water-borne primer based on acrylic for internal wooden laths, doors as well as MDF and fibreboard.
From
£33.82
£28.18
Sika Sikafloor Comfort Porefiller
A two part, low odour, PU leveller and sealer for the Sika-ComfortFloor Pro and Sika-ComfortFloor Decorative Pro Systems.
From
£347.89
£289.91
Centrecoat Epoxy Crack Filler
Easy to use, fast cure for filling cracks and voids in concrete. Can be used at low temperatures.
From
£75.64
£63.03
Teknos Aquafiller 2800 Sanding Sealer
Water-borne air-drying primer for Interior wood.
From
£157.74
£131.45