Hempel Versiline CUI 56990

SKU
id19300
UN1263 (Class: 3, Pk Grp: III)
For long-term protection of hot pipework, equipment and other hot surfaces.
Available in 5 Litres
From £280.72 £233.93
In stock
Only %1 left
Product Description

Hempel Versiline CUI 56990 is a MIO pigmented single component inorganic copolymer coating which cures to form an inert polymer matrix able to resist temperatures up to 650°C/1202°F and thermal shock/cycling in dry or dry/wet service.

Best Uses

Hempel Versiline CUI 56990 is used for long-term protection of hot pipework, equipment and other hot surfaces. Applied directly onto the steel substrate. Specially developed to prevent corrosion under insulation (CUI).

Application

New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to near white metal Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, BN10a, Keane-Tator Comparator 3.0 G/S, or ISO Comparator Rough Medium (G). After blasting, clean the surface carefully from abrasives and dust.

Repair and maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to min. St 2, preferably St 3 (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the performance of the paint. Recommended surface profile is Rz 75-100 micron/3-4 mils, corresponding to Rugotest No. 3, BN10a, Keane-Tator Comparator, minimum 3.0 G/S, or ISO Comparator, Medium (G). After blasting clean the surface carefully from abrasives and dust.

Apply only on a dry and clean surface with a temperature min. 3°C/5°F above the dew point to avoid condensation. Use only where application and curing can proceed at temperatures above: 10°C/50°F. Minimum steel temperature: 10°C/50°F. May be applied on to hot substrates up to maximum 200°C/ 392°F. The relative humidity should preferably be 40-60%, maximum 80%.

Technical Details

Certificates and Approvals

  • Conforms to NACE SP0198 - 2010 systems SS-5 and CS-6
  • Norsok M-501 system no. 1 (Pre-Qualified)

Technical Info

Components: Single Component
Type: Heat Resistant Cating
Finish: Flat
Stock Colours: Dark Grey 10710, Light Grey
Tintable: Please note, bespoke tints are non refundable / exchangeable
VOC Content: 391 g/litre [3.3 lbs/US gallon]
Volume Solids: 74 ± 1%
Suitable Substrates: Steel
Application Method: Airless spray / Air spray /Brush
Theoretical Coverage: 5 m²/litre [203.7 sq.ft/US gallon] – 150 micron/6 mils
Wet Film Thickness (WFT): 200 micron/8 mils
Dry Film Thickness (DFT): 150 micron/6 mils
Induction Time: -
Pot Life: -
Surface Dry: 0.5 hours, 20°C/68°F
Overcoatable: Min: After 6 hours, 20°C/68°F  Max: extended hours at 20°C
Thorough Dry: 1.5 hours, 20°C/68°F
Cleaner / Thinner: Thinner: 08080 . Cleaning of Tools: Hempels Tool Cleaner: 99610
Shelf Life: 1 year at 25°C /77°F
Packaging: Available in 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use