£7.75 delivery on orders excluding certain products & postcodes *
International Intergard 276
SKU
id21086
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A two pack epoxy primer / undercoat / tie coat for internal ship spaces.
Available in 20 Litres
From
£325.55
£271.29
In stock
Only %1 left
Product Description
International Intergard 276 is a two pack epoxy primer / undercoat / tie coat for internal ship spaces.
Best Uses
International Intergard 276 is ideal for use as a primer for dry internal ship spaces such as the accommodation and engine room, and on above water areas, as an undercoat / tie coat between anti-corrosive primers and a wide range of top coats.
Application
Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
As a primer for internal steelwork
Where necessary, remove weld spatter and smooth weld seams and sharp edges. Clean welds and damaged shop-primer by grit-blasting to Sa2 (ISO 8501-1:2007) or by power tooling to Pt3 (JSRA SPSS :1984) or St3 (ISO 8501-1:2007).
As an undercoat / tie coat
The primer surface should be clean, dry and free from all contamination. Areas of breakdown, damage etc. should be prepared to the specified standard (eg. Sa2½ (ISO 8501-1:2007)). Intergard 276 must be applied within the overcoated intervals specified (consult the relevant product data sheet). To avoid pin-holing over inorganic zinc silicate primers, Intergard 276 should be thinned by 15-25% with International GTA220.
Technical Details
| Components: | Two Pack |
| Type: | Solvent Based |
| Finish: | Matt |
| Stock Colours: | EGA080 White |
| Tintable: | No |
| VOC Content: | 293 g/L |
| Volume Solids: | 47% |
| Suitable Substrates: | For internal ship steelwork |
| Application Method: | Airless Spray, Conventional Spray |
| Theoretical Coverage: | 11.75 m2 per litre at 40 microns DFT, allow appropriate loss factors |
| Wet Film Thickness (WFT): | 85 microns |
| Dry Film Thickness (DFT): | 40 microns |
| Induction Time: | - |
| Pot Life: | 16 hours at 10°C |
| Touch Dry: | 40 minutes at 10°C |
| Overcoatable: | See data sheet |
| Hard Dry: | 20 hours at 20°C |
| Cleaner / Thinner: | International GTA220. Thinning is not normally required |
| Shelf Life: | 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. |
| Packaging: | Available in 20 Litres |
Related Products
RODO All Purpose Paint and Varnish Paint Brush
A general contractor all purpose paint brush in various sizes.
From
£2.69
£2.24
International Intergard 251
A two component epoxy anti-corrosive primer pigmented with zinc phosphate for anti corrosive protection.
From
£264.76
£220.63
International Thinner GTA220
Suitable for thinning paints and equipment cleaning from International Paints.
From
£58.87
£49.06
RODO Blackrock Lightweight PU Gripper Gloves
Extremely lightweight gloves with PU coated palms and fingers for exceptional dexterity and grip in wet and dry conditions.
From
£0.77
£0.64
Centrecoat WFT Wet Film Thickness Comb Gauge
An important tool to measure the depth of paint and coatings applied to substrates to ensure the correct thicknesses are applied.
£2.34
£1.95
International Intergard 740
A tough two component epoxy finish coat suitable for concrete that offers good abrasion and chemical resistance in corrosive environments.
From
£443.78
£369.82
International Interzinc 72
A two component, metallic zinc rich epoxy primer, designed to provide excellent corrosion resistance.
From
£422.16
£351.80
RODO Paddle Mixer
Ideal for use as an attachment to a drill to enable the thorough mixing of paints and coatings.
From
£9.24
£7.70