Jotun Penguard Primer

SKU
id17101
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A two component, polyamide cured, high molecular weight epoxy coating designed as a primer for new construction.
Available in 5 and 20 Litres
From £61.06 £50.88
In stock
Only %1 left
Product Description

Jotun Penguard Primer is a two component, polyamide cured, high molecular weight epoxy coating designed as a primer for new construction.

Best Uses

Jotun Penguard Primer can be used as primer as a part of a complete system in atmospheric and immersed environments. Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop primed steel and thermally sprayed zinc substrates.

Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.

Application

To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. For Carbon Steel, prepare to Sa 2.5. For Stainless Steel or Aluminium, prepare via abrasive blast cleaning to achieve a surface profile using approved non metallic abrasive media which is suitable to achieve a sharp and angular surface profile. For Galvanised Steel, prepare by light brush blasting using non metallic abrasive leaving a clean, rough and even pattern. For Shop Primed Steel, abrasive sweep or alternatively blasted to Sa 2 (ISO 8501-1) of at least 70% of the surface. for Coated Surfaces, clean, dry and undamaged compatible coating (ISO 12944-4 6.1.4). For Concrete, allow a Minimum 4 weeks curing. Moisture content maximum 5 %. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove laitance.

Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Use airless spray. Brush is recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness.

Technical Details

Approvals

When used as part of an approved scheme, this material has the following certification:

  • Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8
  • Norsok M-501 System 6A
  • Norsok M-501 System 6B

Technical Info

Components: Two Part
Type: Polyamide cured, high molecular weight epoxy coating
Finish: Matt
Stock Colours: Grey and Red
Tintable: No
VOC Content: 456.0g per Litre
Volume Solids: 51%
Suitable Substrates: Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop primed steel and thermally sprayed zinc substrates.
Application Method: Airless Spray, with Brush for stripe coating or small areas
Theoretical Coverage: 8.5 - 12.8 m2 per litre
Wet Film Thickness (WFT): 80 - 120 microns
Dry Film Thickness (DFT): 40 - 60 microns
Induction Time: 30 mins at 23°C
Pot Life: 8 hours at 23°C
Touch Dry: 2 hours at 10°C
Overcoatable: 8 hours at 10°C
Fully Cured: 14 days at 10°C
Cleaner / Thinner: Jotun Thinner No. 17
Shelf Life: 24 months for Part A, 48 months of Part B
Packaging: Available in 5 and 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use