Soppec Tracing Plus Acrylic Line Marking Aerosol

SKU
id18841
UN1950 (Class: 2.1)
A high quality acrylic line marking paint with a satin finish, superb for interior walkways and other health and safety markings.
Available in Boxes of 6 x 750ml Aerosols
From £133.20 £111.00
In stock
Only %1 left
Product Description

Soppec Tracing Plus Acrylic Line Marking Aerosol is high quality acrylic line marking paint with a satin finish, superb for interior walkways and other health and safety markings.

Best Uses

Soppec Tracing Plus Acrylic Line Marking Aerosol typically uses for this product are any type of interior delineation, such as line, walkway and stencil marking, also hazard zoning and lean management.

  • High covering opacity ensures quality line
  • Crisp line formed by unique nozzle
  • Fast drying
  • Satin finish makes it easier to clean

Application

All surfaces must be free of any dust, damp or contamination. Shake the can vigorously upside down to mix the paint thoroughly (even after balls rattle).

Concrete:
Before applying Tracing Plus on new concrete, wait for 3 to 4 weeks to allow the concrete to dry (DTU standard) and the acid evaporation. Greater amounts of aerosol will be required for line marking on coarser concrete.

Asphalt:
It is advisable to wait at least 15 days before marking on a new asphalt coating to avoid damage to the paint. Depending on the climate conditions after laying the asphalt, this period may have to be extended by one or two weeks.

Painted Surfaces:
Tracing Plus is suitable for most floor coatings, however a compatibility test is always recommended prior to applying markings.

Apply either manually or with application equipment. Use upside down and adjust height of application in accordance with your required line width. Shake the can vigorously upside down to mix the paint thoroughly even after balls have been heard clearly. The surface to be painted must be well prepared for an excellent adherence of the paint. Clean surface to be free of dust, dirt and grease. At the time of application, surface must be dry and temperature not less than 5°C for optimal performance.

For a good quality line, the first application must be a thin coat. The second and possibly third must be carried out more slowly so that a good deposit of paint is achieved. Purge can in upright position (until only gas is released), to clean the valve and diffuser. Do not apply when the air or surface temperature is below 5°C or less than 3°C above dew point, or if this is likely to occur during the curing period. Do not apply when there is rain, mist, fog, or snow imminent; when humidity is high or the surface is wet with condensation or likely to be during the drying period.

To ensure the best cleanable finish, lines can be covered by Meon Protect Line varnish to increase time lasting and resistance to dirt. Use water and mild detergent to wash line.

Technical Details
Components: One Part
Type: Aerosol
Finish: Satin
Stock Colours: White, Yellow, Black, Blue, Green, Orange and Red
Tintable: No
VOC Content:
Volume Solids:
Suitable Substrates: For concrete, asphalt or previously painted surfaces
Application Method: Aerosol - use either manually or via a line marking machine capable of aerosol release of paint
Theoretical Coverage: Typically 80m line @ 50mm per 750ml Aerosol
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: -
Pot Life: -
Touch Dry: 5 - 10 minutes at 15°C
Overcoatable:
Traffic Ready: 15 - 20 minutes at 15°C
Cleaner / Thinner:
Shelf Life: 12 months when stored under cover, in original unopened containers
Packaging: Available in Boxes of 6 x 750ml Aerosols

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use