Owatrol Aquanett is powerful ready to use wood oil cleaner formulated to remove all teak oils and other oils from all types of exterior wood, it is perfect to remove oils from both horizontal and vertical timber surfaces such as decking, garden furniture, cladding, timber structures plus many more.
Owatrol Aquanett is formulated to remove previously applied oil finishes from all types of exterior timber that have been blackened by UV rays, it can also be used to remove the mill glaze from new timber and also as a powerfully wood cleaner for severely weathered timber thus improving the adhesion and penetration of any freshly applied finish, also being of gel consistency means the product will not run making for easy application onto vertical surfaces.
Aquanett is biodegradable, solvent and paraffin free so is perfect for use in environmentally sensitive areas.
Owatrol Aquanett can be used to remove both oils and mill glaze from both new and old weathered exterior timber. It can be applied to all exterior softwoods, hard woods, pressure treated wood and thermowood on both vertical and horizontal surfaces. Owatrol Aquanett is perfect for application on garden furniture, decking, cladding, timber structures plus many more.
Please note: Some products such as Liberon oil may be difficult to remove. Please call for advice.
Always carry out a preliminary test prior to commencing the job. Wear chemical resistant gloves, safety goggles and protective clothing. Hardwoods inc’ exotic hardwoods and woods rich in tannins i.e. Cedar, Oak, Teak, Ipe... may darken with Owatrol Aquanett.
Where Owatrol Aquanett has darkened the wood DO NOT allow it to dry, prior to using Owatrol Net-Trol. Treat stripped wooden surfaces with Owatrol Net-Trol to restore the woods original colour. Cover and protect everything you do not wish to strip, including plants and shrubs and any aluminium surfaces. When stripping vertical surfaces, work from bottom to top to avoid streaking. Apply between 5°C and 35°C. Do not apply in direct sunlight or on a hot surface.
Do not allow Owatrol Aquanett to dry on the surface. If drying occurs dampen with a mist application of water.
Remove any loose and flaking finish. Brush off any physical surface contamination i.e. moss, general dirt etc.
Removal of Oils and Millglaze. Apply a thick coat of Owatrol Aquanett over the whole surface to be stripped. For large areas work in zones. Allow product to work (max 5 minutes). Scrub surface with stiff nylon scrubbing brush while flushing with water, alternatively use a pressure washer (max. 60 bars / 870 psi). Thoroughly rinse the surface after stripping with fresh clean water. After stripping and rinsing, surfaces must immediately be treated with Owatrol Net-Trol while still wet to neutralise the surface.
NB: The use of hot water makes the job easier. Consult us for additional information and advice prior to using Owatrol Aquanett on Oak and Chestnut.
|Type:||Solvent Free Gel|
|VOC Content:||< 0.05 g/L|
|Suitable Substrates:||For all exterior woods|
|Application Method:||Synthetic Brush, Synthetic Roller|
4 m2 per litre.
Actual coverage will vary depending on application method, type, texture, age and porosity of the wood.
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Cleaner / Thinner:||Water|
|Shelf Life:||2 years in original unopened packaging. Store unused portion in a tightly closed plastic or glass container. Do not store in metal containers. Keep from freezing and high temperatures.|
|Packaging:||Available in 1, 2.5 and 10 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.