Designed for interior and exterior applications. Bedec Aqua Advanced has been innovatively designed, something in common with other Bedec products, to incorporate high quality, water-based technology. It is this modern technology that creates the finish you would expect from a leading brand name like Bedec.
Bedec Aqua Advanced SATIN is an extremely fast drying product that exhibits great durability, levelling and colour retention. It dries to provide users with a smooth enamel finish in either gloss or satin. It is also available as a primer. With a variety of uses and finishes, the versatility of Aqua Advanced puts it high up on our list of favourite products, which we have tried and tested ourselves. Promain understands how important it is for you to get a high-end product and high quality finish every time; which is why we choose to supply this paint.
Ensure the surfaces to be painted are clean dry and free from dust, dirt grease and wax. Remove all loose and defective paint. Algal and fungal growths should be removed and treated with a fungicidal wash. Smooth glossy surfaces should be lightly abraded to provide a key. Bare steel should be free from rust, scale and dust. Before applying Bedec Waterbased All Metals Primer. Pressure treated timber should be weathered for at least six months prior to painting. Denatured wood should be abraded to reveal new cells. New planed, finished wood or PSE wood should also be abraded to open the grain and allow maximum penetration.
Where there is a risk of staining (Extractive discolouration) treatment with Bedec Stain Block is recommended. It is always advisable to test for staining by applying Aqua Advanced Enamels to a small area first. Knots should also be treated with Bedec Stain Block, Knotting solution is not recommended.
Apply by brush, roller, conventional H.V.L.P or airless spray. Stir well and check colour before use. Do not apply at air or surface temperatures below 8°C or when likely to rain before the paint has fully dried. On sealed surfaces apply two to three coats, allowing each coat to dry thoroughly. Do not over spread.
Bedec Aqua Advanced works well when applied in outdoor conditions but is ideal for interior coatings too. It results in a finish that will not yellow when exposed to sunlight. Suitable for application to most wooden substrates such as stair banisters and wooden indoor and garden furniture.
|Type:||Water based Acrylic / Polyurethane Enamel|
|Stock Colours:||Black and White|
|Tintable:||Upon Special Request, Depending on Quantity. Please note, bespoke tints are non-refundable / exchangeable.|
|VOC Content:||30.0g per Litre|
|Volume Solids:||50% (White)|
|Suitable Substrates:||Bare Steel and Wood|
|Application Method:||Brush, Roller, Conventional H.V.L.P or Airless Spray|
|Theoretical Coverage:||13 -15 m2 per litre per coat|
|Wet Film Thickness (WFT):||71 microns|
|Dry Film Thickness (DFT):||27 microns|
|Touch Dry:||2 - 4 hours at 18°C|
|Overcoatable:||4 hours at 18°C|
|Cleaner / Thinner:||Clean up with warm soapy water|
|Shelf Life:||24 months|
|Packaging:||Available in 1, 2.5 and 5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.