Centrecoat Procure 15 Floorcoat

SKU
id23721
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A two pack, professional grade, fast return to service floor coating.
Available in 5 and 20 Litres
From £116.72 £97.27
In stock
Only %1 left
Product Description

Centrecoat Procure 15 Floorcoat is a two pack, professional grade, fast return to service floor coating.

Best Uses

Centrecoat Procure 15 Floorcoat is a anti-slip two pack floor paint with a quicker return to service than standard epoxy systems. If applied correctly, return to service can be the following day, which far quicker than similarly priced epoxy systems.

  • Fast drying, slip resistant floor coating
  • Overnight return to service for foot traffic
  • Isocyanate free and suitable for fork lift areas
  • EU Directive 2004/42/IIB(j)(500)484 compliant
  • SRV is 86 (dry), extremely low slip potential

Typical applications environments include warehouses, factories, demarcation of pedestrian areas, and steps.

Application

All substrates must be clean and dry, free from oils, grease, dust and dirt. Mechanical preparation such as vacuum blasting is the preferred method, particularly on power floated floors. Oils and greases should be removed by steam cleaning. If aqueous cleaning solutions are used the substrate should be allowed to thoroughly dry. Moisture content should not be in excess of 6%.

Power floated floors present the most challenging substrate on which to achieve an acceptable bond. Where possible, the surface should be mechanically abraded to achieve a surface profile. As an alternative or when this process is not permitted, Centrecoat Adhesion Promoter should be used.

Sound previously painted surfaces can be over painted although the following points should be followed:

  • Check adhesion of the coating to the substrate. Never overcoat if the coating is loose or flaking.
  • Check the compatibility of the coatings. This can be done by selecting an area approx. 1m2 and carrying out a test application. Strong solvents can have the effect of lifting the original coating from the substrate or wrinkling the previously applied coatings.
  • If used for line marking on tarmacadam it should be aged for minimum 6 months to prevent bleed through or softening of the tarmacadam. A trial area is always recommended if unsure.

Follow guidance on product data sheet.

Technical Details

Slip Resistant Value

  • Dry – 86 (TRRL SLIDER 55 ), Extremely Low Slip Potential
  • Wet – 45 (TRRL SLIDER 55)

Technical Info

Components: Two Pack
Type: Solvent Based
Finish: Satin (with slip resistant additive)
Stock Colours:  Light Grey (00-A-05), Dark Grey (18-B-25), Safety Yellow (08-E-51)
Tintable: Yes, subject to MOQ of 200L - POA. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 500 g/l
Volume Solids: 40% depending on colour
Suitable Substrates: Concrete Internal Flooring
Application Method: Brush, Deep Pile Roller, Airless Spray, Air Assisted Airless Spray
Theoretical Coverage: Theoretically approx 6-8 square metres per litre.
5 litres provides enough to cover approx 30m2 of floor depending on condition of substrate.
Wet Film Thickness (WFT): 185 microns
Dry Film Thickness (DFT): 100 microns
Induction Time: -
Pot Life: 6 - 8 hours at 20°C
Touch Dry: 30 minutes at 20°C
Traffic Ready: Overnight at 20°C
Fully Cured: 5-7 days at 20°C
Cleaner / Thinner: Gunwash
Shelf Life: 6 months in unopened containers when stored under cover within the temperature range 5 - 35°C.
Packaging: Available in 5 and 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Related Products